# pult·energy — Power, battery, home heating

> Power, battery, home heating (iPhone/iPad app by Kyrylo Guliaiev.)

- Source: https://appshunter.io/ios/app/pultenergy/id6827269683 (this page in markdown: same URL + `.md`)
- Developer: [Kyrylo Guliaiev](https://appshunter.io/developer/1779226458)
- Category: Utilities, Lifestyle
- Price: Free
- Age rating: 4+
- Requires: iOS 26.0 · 22 MB
- Languages: American English, Ukrainian
- Released: 2026-10-31
- Data updated: 2026-11-18

## What is pult·energy?

pult·energy puts the power and heat at home under control. What's going on with the grid and the battery, how long it lasts, when the schedule says the power is due back - and the inverter, devices and room temperatures you run from your phone, watch or Mac.

Got a hybrid inverter with a battery? pult·energy lets you see your home and set it up from anywhere.

YOUR HOME ON ONE SCREEN
• Is the power on, the charge in % and in kWh above the discharge floor, how much the home draws
• «Lasts ~17 h» - from your home's usual consumption in the hours ahead
• During an outage - a timer, the scheduled switch-on time and whether the charge lasts until then

THE SCHEDULE - WHAT'S AHEAD AND WHAT HAPPENED
• The charge since midnight and a forecast to the end of the day; how far and by when the battery will charge - and why
• Outages now, next by schedule and already over
• Schedule against the fact: «power beyond plan», «no power beyond plan» - by day, week and month

INVERTER AND BATTERIES - FROM THE APP
• The emergency reserve, charge speed, charging from the grid and a generator, where solar goes first - each explained
• Before a risky change - what can go wrong and a second «yes»
• Sets of settings for weekdays, weekends, winter and summer; any change can be rolled back
• Inverter faults in words, not codes

AUTOMATION - EACH ONE IS A SINGLE SWITCH
• Charge to 100% before an outage, a morning reserve, devices back one by one
• Night charging on the cheaper rate, expensive hours on the battery
• Gentle charge, main breaker protection, surplus solar to the boiler

DEVICES - ON THEIR OWN AND WITH ONE TAP
• Shelly, Tuya / Smart Life, TP-Link Tapo sockets and relays - over your home network
• Power goes - the boiler and floor heating switch off within 10 seconds; the washer isn't stopped mid-wash
• Rules in sentences: by time, sun, charge, temperature and power state. «Explain» tells you what will happen, the log - why a rule didn't run
• Timer, cycle, pulse, a daily run-time limit, running on the battery down to the charge you set
• A meter for every device: how much it took and from where - grid, battery, solar

ROOMS AND HEATING
• Tuya / Smart Life thermostats by room: the temperature, the target and what the room is doing
• A temperature schedule for weekdays and weekends
• Smart start heats ahead, and learning measures how fast your room warms up
• Scenes: «Night», «Away», «Home» - devices and rooms together

YOU KNOW FIRST
• Power gone and back, low charge, «Schedule updated», 30 minutes before an outage
• A silent hourly report during an outage
• Live Activity, Dynamic Island, widgets with buttons for devices, scenes and thermostats
• Apple Watch: the app, complications, Smart Stack
• Telegram for the whole family - everyone joins with their own code

STATISTICS AND COSTS
• Charts for the day you pick, from a minute to a week
• The energy balance and the bill on one, two or three tariff zones
• Export to Excel

FOR THE WHOLE FAMILY, ON EVERY SCREEN
• People and roles, timed access - 2 hours, a day or a week
• Several homes in one account
• On Mac - all of it on a big screen, home status in the menu bar
• The pult.energy dashboard - in any browser

WHICH DEVICES FIT
• Find the model, get the steps or ask the assistant
• "Add a device" in three steps: Shelly relays, Tapo and Tuya plugs
• Zigbee temperature and humidity sensors: tap "+ Sensor"

PRIVACY
• Inverter data over a cable, no manufacturer cloud
• The phone-to-home link is encrypted
• No ports to open on your router
• No ads, no third-party analytics

WHAT YOU NEED
• A Deye hybrid inverter with a battery
• pult·controller next to the inverter, an RS485 cable
• A pult account - email, Apple or Google
• The outage schedule - Yasno (DTEK)

The app is free. Everything is free for the first 30 days after connecting a home.

No equipment yet? Open the demo: the app shows a real apartment.

pult·energy is a pult product. Support: pult.energy/support

## Is pult·energy safe?

Not enough ratings yet to assess pult·energy.

## Is pult·energy legit?

pult·energy appears legitimate, with a few gaps. The AppsHunter Legitimacy Score for pult·energy is 65 out of 100 points across 7 verification signals from App Store and developer data.


## Version history (last 5 releases)

### 1.7 — 2026-11-16

Temperature and humidity sensors in every room - and new devices you add right from the app.

ZIGBEE SENSORS
- "+ Sensor": pult·controller searches for 2 minutes, you hold the button on the sensor - and it's in your home
- Zigbee temperature and humidity sensors (Sonoff, Aqara and others)
- A sensor tile in Controls: temperature to a tenth, humidity and battery; a warning when the battery runs low
- The sensor screen: temperature and humidity charts for a day, a week and a month, the day's low and high
- Assign a sensor to a room - the room chart, smart start and learning then go by it, not by the radiator thermostats
- You need a Zigbee USB receiver in pult·controller (Sonoff ZBDongle-E) - pult·controller sets up the rest

ADD A DEVICE - FROM THE APP
- "Add a device" in three steps: search, setup, done
- Shelly relays - over Wi-Fi and Bluetooth
- TP-Link Tapo plugs: sign in to Tapo once per home
- Tuya plugs: the key from Smart Life or entered by hand
- Device not on the list - enter its IP address
- The Tapo password and the Tuya key travel to pult·controller end-to-end encrypted

WEATHER
- Wind gusts in the forecast

ROOMS
- Climate explains why heating starts at exactly that time

### 1.6 — 2026-11-14

pult·energy is now on iPad, with a weather forecast for your home and an answer to whether your equipment will work.

IPAD
- A wide layout like on Mac: sidebar, card Overview and Split View
- Extra large Home widget: charge, today's schedule and devices

WEATHER
- Forecast for your home city: now, 12 hours and 3 days
- Hours without power on the schedule are marked - see the weather while the house runs on battery
- Thunderstorm, strong wind, heavy snow or frost - a warning and until when pult·controller keeps the battery full
- How much your solar panels will give, by the forecast

WILL MY EQUIPMENT WORK
- Look up your inverter, battery, relay or thermostat and see whether it works with pult·controller
- Not on the list - "Ask to add", with a photo of the label if you like
- "My requests": where your request stands; you get a notification as soon as the model works

OVERVIEW
- "Will the battery last": your usual outage and how long the battery lasts on the current charge
- Phases over the week and which device to move to another phase
- Voltage over the week: how many times it went out of range
- A hint to turn on load shedding if the inverter tripped on overload

SCENES AND CONTROLS
- A scene runs on its own: at a time, by the sun, by charge, before or after an outage, when the power goes or comes back
- "The bot is in charge now" - which mode holds the charge and when your value comes back

COSTS
- This month: spent, forecast and limit
- Weekly and monthly report
- Solar surplus: what to run during the day

ALSO
- "Invite" someone right from the app: role and access for 2 hours, a day, a week or forever
- Support ID in Settings

### 1.5 — 2026-11-12

Heat in every room, device rules in plain sentences, and new relays without anyone else's app.

ROOMS AND HEATING - the new «Rooms» section
- Tuya / Smart Life thermostats by room: the room temperature from all its thermostats and what it's doing - heating, holding or cooling
- A target for the whole room with − and +; hold to change faster
- Room schedule: what temperature, when and on which days, weekdays and weekends apart
- Smart start: to have 22° at 06:30, pult·controller starts heating ahead, adjusted for the weather
- Learning: pult·controller measures how fast a room heats up and cools down - several rooms at once
- Changed the temperature by hand - it holds until the next schedule point, for 2 hours or until you return to auto
- Scenes now cover rooms: «Away» - cooler everywhere, «Home» - back to the schedule
- A thermostat warns you when its battery runs low

DEVICE RULES
- All of a device's rules on one screen, in sentences: when to turn on, when to turn off and when not to turn on
- New events: room temperature, «the device has finished», the «only from … to …» condition
- «Explain» - exactly what pult·controller will do; «Play» - what happens if the power goes now
- «When power is lost» - the device's mode right on its card
- A device week and a log: what happened and why a rule didn't run
- During an outage a device can run on the battery while the charge stays above your level, within a daily limit
- A ready «Boiler» rule set

INSIDE A DEVICE
- Where a device took its energy: grid, battery, solar, generator - and what the grid part cost
- Charts by day and for 24 hours, with a «usual» line

NEW DEVICES
- pult·controller puts a new Shelly relay on your Wi-Fi over Bluetooth - no Shelly app needed
- Smart Life: choose which devices from your account to show

CONTROL
- Three parts: appliances, heating, inverter and battery
- «Quick»: grid charging and its speed
- A command shows its progress in steps: sent, received by pult·controller, accepted

WATCH AND WIDGETS
- Devices, scenes and thermostats as buttons; you choose what to show

ALSO
- Timed access for another person: 2 hours, a day or a week
- Notifications from all your homes

### 1.4 — 2026-11-11

You can now run your inverter and battery from the app, and the bot on the Pi takes care of the automation.

INVERTER CONTROL
- Inverter settings, each explained: how much charge to keep for emergencies, how fast to charge, when to use the grid or a generator, where solar power goes first
- Before a risky change the app tells you what can go wrong and asks you to confirm again
- Sets of settings: save your own and write them to the inverter with one tap; roll back a change that didn't work out
- Your own set for weekdays, weekends, winter and summer - the bot switches them itself
- Inverter faults in words, not codes

AUTOMATION - turned on in «Control»

Outages
- Charge before an outage: the bot charges the battery to 100% ahead of the Yasno schedule
- Last until the outage ends: if the charge won't last until the power is back, the bot turns off non-essential devices early
- Morning reserve: during a night outage the bot keeps charge for the morning
- Load shedding: the inverter is about to overload - extra devices go off and come back later
- Use the reserve at the end: power is due back soon - the bot lets the home use part of the emergency reserve
- Power back - devices come on one by one, not all at once

Tariff and grid
- Charge at night on the cheaper rate, run on the battery by day - never below the level you set
- Expensive hours on the battery: with a three-zone tariff the home runs on the battery at peak hours, not on the grid
- Don't trip the main breaker: the home draws too much from the grid - the bot turns off non-essential devices until it drops
- Monthly spending limit: the bill is growing faster than you want - a warning and what uses the most

Battery
- Gentle charge: while no outage is coming, the battery stays below 100% and lasts longer; before an outage - to 100%
- Slower charging in the cold and when the inverter is hot, to protect both
- Once a month to 100%, so the battery shows its charge correctly
- «Charge now» - once, then back to normal; «Away from home» - extras off, gentle charging

Weather and sun
- Get ready for bad weather: a storm, strong wind or frost in the forecast - the battery is fully charged in advance
- Sunny tomorrow: less charging from the grid at night, the panels top it up
- Solar surplus to an appliance: the battery is full and the panels give more than the home uses - a chosen appliance, like the boiler, turns on

Generator and devices
- Generator through a relay: no power and low charge - the bot starts the generator itself; never at the hours you set
- A daily run-time limit for a device

Reports and maintenance
- Daily, weekly and monthly reports, a battery health report, quiet hours - silent except alarms
- Alerts on bad grid voltage and tips on spreading devices across phases more evenly
- Pause for repairs: while an electrician works, the bot doesn't switch or change anything
- Once a month - a generator test run and a trial outage: will the battery last a usual outage

CHARTS - in Statistics, for the day you pick, from a minute to a week
- Battery and power, power by schedule and in reality, where the home's power came from, charge and discharge, taken from the grid, load and voltage on every phase, battery charging and temperature, your own set
- Compare with the past week or month, and «Today vs usual»
- Pinch to zoom

THE SCHEDULE SCREEN
- The charge since midnight - and what it will be to the end of the day
- What % the bot will charge the battery to, by when - and why
- Outages: now, next by schedule, already over - and whether the battery charges in between
- How much power the schedule promised and how much there really was - by day, week and month, export to Excel, PDF or an image

ALSO
- «Control» highlights what is acting right now
- Typical usage as a 24-hour dial
- The charge ring on the lock screen, in Dynamic Island and widgets shows the state: green with power, orange on battery, red when low

### 1.3 — 2026-11-09

Now you set up the inverter right from your phone - with an explanation for every option.

- Inverter: battery reserve for emergencies, fastest charge, charging from the grid and a generator, how much to take from the grid, where solar goes first, overheating protection. Before a risky change the app tells you what can go wrong and asks for a second «yes»
- Sets of settings: «Standard» and your own, for weekdays, weekends, winter and summer. Clone one, set an hourly schedule and write it to the inverter with one tap. A check tells you what to fix, and every change can be rolled back
- Inverter faults in words, not codes; dangerous ones in red
- «Devices» is now «Control»: relays, inverter and automation in one place, with an ⓘ explanation and an animated diagram for every item
- Devices like smart plugs: timer, schedule, by the sun, cycle, pulse. Plus a daily run-time limit, a rule by charge, a switch-off order, a delay after power returns and «Turn all off / Turn all on»
- Scenes - with one tap
- Every home setting in the app: tariff, relays, scenes, people and roles with temporary access, batteries, maintenance, backup, updates for the program on the Pi, address for the schedule, equipment, export to Excel
- Charts: compare with last week or four weeks, «Today vs usual», «Cold and charging», voltage on every phase with outages marked, solar and generator, steps from one minute
- During an outage the ring tells you right away whether the charge lasts until power is back
- Every outage: when it went, when it came back, how long it lasted and how much battery it used
- «Lasts for» shows what the estimate is based on; battery in kWh
- Device switches right on the Overview; another home - tap its name
- «Which devices fit»: model search, connection steps and an assistant chat
- Smart Stack on Apple Watch; the hourly outage report arrives silently
- New name - pult·energy, dashboard at pult.energy

## Apps similar to pult·energy

| App | Rating | Price | Category |
| --- | --- | --- | --- |
| [Svitlo: power outage schedule](https://appshunter.io/ios/app/svitlo-power-outage-schedule/id6825263037) | — | Free | Utilities |
| [Meter Tracker: Water Gas Power](https://appshunter.io/ios/app/meter-tracker-water-gas-power/id6788378032) | — | Free | Utilities |
| [SvitloUA](https://appshunter.io/ios/app/svitloua/id6759189278) | — | Free | Utilities |
| [Черги відключення Черкаси 2026](https://appshunter.io/ios/app/2026/id6757957420) | 5.0 (1) | Free | Utilities |
| [APEXpulse Battery Control](https://appshunter.io/ios/app/apexpulse-battery-control/id6762008373) | — | Free | Utilities |
| [Rada: Законопроєкти](https://appshunter.io/ios/app/rada/id6767016634) | — | Free | Utilities |

## More apps by Kyrylo Guliaiev

- [DayDone: Day Planner](https://appshunter.io/ios/app/daydone-day-planner/id6738076997)
- [AtomNews](https://appshunter.io/ios/app/atomnews/id6746642932)
- [AtomKeys – Smart Keyboard](https://appshunter.io/ios/app/atomkeys-smart-keyboard/id6755686807)
- [Qopa: Couples Budget Tracker](https://appshunter.io/ios/app/qopa-couples-budget-tracker/id6796833861)
- [Plio Music](https://appshunter.io/ios/app/plio-music/id6797504761)
- [Plio Business: venue music](https://appshunter.io/ios/app/plio-business-venue-music/id6802431367)

All apps by Kyrylo Guliaiev: https://appshunter.io/developer/1779226458

---

*Data collected daily from the US App Store and indexed by [AppsHunter](https://appshunter.io/). User reviews are verbatim App Store reviews. Ratings, prices and chart positions refresh continuously; this snapshot is from 2026-11-18.*
