# Rafter & Stair Layout — Roof Pitch Finder & Stringers

> Roof Pitch Finder & Stringers (iPhone/iPad app by Dmytro Antoniuk.)

- Source: https://appshunter.io/ios/app/rafter-and-stair-layout/id6834170589 (this page in markdown: same URL + `.md`)
- Developer: [Dmytro Antoniuk](https://appshunter.io/developer/6827302145)
- Category: Utilities, Productivity
- Price: Free
- Age rating: 4+
- Requires: iOS 16.4 · 42 MB
- Languages: American English
- Released: 2026-11-13
- Data updated: 2026-11-18

## What is Rafter & Stair Layout?

You are on the plate with a tape in one hand, the span is 23' 7-1/2", the pitch is 7/12, and you need a rafter length you can mark. Or the stair opening is framed and the inspector is coming Thursday. This app does that math, shows how it got there, and draws the cut.

Roof pitch from the phone
Lay the phone on the roof deck or on the top edge of a rafter and read the pitch live, as x/12 and in degrees. Hold the number when it settles, calibrate once on a level floor, then send it to the rafter, hip or roof squares screen. If you would rather trust your level, type its angle.

Rafters, hips and the roof
• Pitch from rise and run, or the other way, with angle and factor
• Common rafter: line length, tail, overall length, plumb and level cuts, bird's mouth, ridge already taken off
• Hip and valley: hip length, side cuts for the square and the saw, and every jack length at 16" or 24" on center
• Roof squares for gable and hip roofs, with your waste, plus bundles, ridge cap, eave and starter
• Drawings to mark from: the whole rafter on the wall, the seat and tail up close with the bird's mouth dimensioned, and a hip plan with each jack numbered

Stairs that pass
Type the floor to floor rise. You get risers, treads, total run, stringer length and the cut points to mark on the stringer, drawn on the stringer with each step numbered. Every IRC 2021 R311.7 limit gets its own pass or fail row with the section number. If your town amends the code, put your own riser and tread limits in Settings.

Fractions the way a tape reads
The tape screen has feet, inch and fraction keys, so 5' 6-1/2" + 3' 8-3/4" comes back as 9' 3-1/4". Answers round to 1/16" or whatever mark you pick, down to 1/32". Metric works too.

Lumber
Board feet and cost, wall studs with corners and openings, layout marks at 12", 16", 19.2" or 24", and floor joist counts.

On site
Name a calculation and save it as a job, add a note like the lot number, duplicate it for the next house, and share the numbers as plain text with whoever is cutting. Jobs you opened last sit on top. It works without signal. Every screen has a section that explains the formula and where each number comes from. Codes differ by town, so check yours before you build.

## Is Rafter & Stair Layout safe?

Not enough ratings yet to assess Rafter & Stair Layout.

## Is Rafter & Stair Layout legit?

Rafter & Stair Layout appears legitimate, with a few gaps. The AppsHunter Legitimacy Score for Rafter & Stair Layout is 65 out of 100 points across 7 verification signals from App Store and developer data.


## Version history (last 4 releases)

### 1.2.0 — 2026-11-17

Metric stairs now read in mm everywhere, and switching units converts the lengths you already typed.
Number fields take fractions such as 7 1/2 for the pitch, and a comma works as the decimal mark.
Error messages name the field and say what to type. A span too large to be real gets a clear message instead of a huge number.
The tape says Cannot divide by zero instead of showing a blank.
Labels on the rafter seat detail and the stair stringer drawing no longer overlap.
Rename a saved job from the Jobs menu. A duplicated job is named copy 2, copy 3 instead of copy copy.
Stringer cut points read 5' 0-15/16" instead of 5' 15/16", and opening a saved job keeps your unsaved numbers.
Settings shows the mm rounding in metric mode, and shared results end with a link to the app.
The Home Screen name is now Rafter&Stair, to match the store name.

### 1.1.0 — 2026-11-15

• Measure roof pitch with the phone: lay it on the roof or a rafter, hold the reading and send it to the rafter, hip or squares screen
• See the cut on a drawing: rafter on the wall, seat and tail detail, stair stringer with numbered steps, hip plan with the jacks
• Jobs: add a note, duplicate a job, and the ones you opened last come first
• The app reopens where you left off more safely after an update

### 1.0.1 — 2026-11-14

• Stair and rafter results now show at one size, so the two numbers on top line up
• The fraction dash key on the tape is labeled, so 6-3/4 is easier to type
• Saving a job suggests a name that fits the screen you are on
• In metric, the stair comfort rule reads in mm
• Shared text ends with the new app name
• New help and privacy pages at framing.antonyuk.org

### 1.0.0 — 2026-11-13

No release notes.

## More apps by Dmytro Antoniuk

- [Screenpile: Screenshot Cleaner](https://appshunter.io/ios/app/screenpile-screenshot-cleaner/id6827302143)
- [Concrete Calculator Foundation](https://appshunter.io/ios/app/concrete-calculator-foundation/id6828890064)
- [WinWin: Daily Wins Journal](https://appshunter.io/ios/app/winwin-daily-wins-journal/id6828890198)
- [Conf Circles: Event Contacts](https://appshunter.io/ios/app/conf-circles-event-contacts/id6828890200)
- [Volo: Hobby & Bucket List](https://appshunter.io/ios/app/volo-hobby-and-bucket-list/id6828890209)
- [Outage Power](https://appshunter.io/ios/app/outage-power/id6834169714)

All apps by Dmytro Antoniuk: https://appshunter.io/developer/6827302145

---

*Data collected daily from the US App Store and indexed by [AppsHunter](https://appshunter.io/). User reviews are verbatim App Store reviews. Ratings, prices and chart positions refresh continuously; this snapshot is from 2026-11-18.*
