SunPower Pro Connect

August 7, 2024

Upgrades the scanner application in Pro Connect

June 18, 2024

Improvements: The Tesla storage option is available in every state. The Power Control System (PCS) feature is now available for single-inverter SunVault storage systems. Bug Fixes: Resolves the issue where the app does not retain the PVS Wi-Fi network credentials during return visits

May 29, 2024

Improves the display of variables during SunVault System Checks. Places third-party storage information behind a dedicated feature flag. Enhances iOS builds for the Apple App Store.

March 14, 2024

Improvements: New feature notifies users when the PVS they are connected to is experiencing excessive flash memory wear. This alert serves as prompt for technicians to initiate a RMA for the affected PVS and to replace it with a new PVS to ensure optimal site performance. The scanning feature has been enhanced to better scan third-party battery serial numbers. Bug Fixes Fixed a bug that prevented users from returning to the previous screen while viewing “Errors and Warnings” on the “Error Detail’s” screen during the “System Check” report. Fixed a bug that occurred in the Configure tab; when clicking "Submit Configuration," it incorrectly displayed an "Error While Setting Export Limit" message.

February 9, 2024

Improvements: Ability to add third party storage information. Improved Ethernet connection detection. Clarified the RSE information text on System Configuration page. Bug Fixes Fixed an issue where the RETRY CONNECTION button would not appear after finishing the PVS FW Upgrade. The GO BACK button on the PCS modal is again functional.

January 23, 2024

Improvements: (Enphase features will be rolled out gradually) - Ability to commission Enphase storage systems in meter-only configuration. - Enphase storage system serial number is captured in commissioning report. - We now verify the serial number of the PVS every 5 minutes to ensure you are connected to the PVS you are commissioning.

December 22, 2023

Improvements: - Ethernet support for PVS6 commissioning: You can now connect to a PVS using an ethernet adapter and commission the system. This aims to provide an alternate mode of connection to the PVS where you do not have to wirelessly connect to the PVS6 access point over WiFi, ensuring higher reliability of connection. - Ability to add Enphase storage information in ProConnect: With this feature, you can now add Enphase storage details through ProConnect. This is independent from commissioning Enphase storage in the Enphase commissioning application. This feature will be iteratively rolled out to more users. Bug Fixes: - The "We could not find onboard meters. Please run discovery again" banner was appearing even when meters were found. This issue has now been fixed. - A bug caused the “We couldn’t set the operational state, please try again” error to appear even after successfully setting the operation state. This should no longer happen.

December 13, 2023

Improvements: Additional messaging during PVS5 commissioning to provide you with next steps when required. Improved messaging on Manage Firmware screen when certain firmware packages fail to download. Bug Fixes: Sometimes if your device loses connection to the "PVS" after connecting to it on "SELECT A PVS" screen the modal "Please reconnect to the PVS" was not be shown - this has now been fixed. Fixed an issue causing occasional app crashes.

October 27, 2023

Improvements: You can now enable panel level monitoring directly from ProConnect. This is available in the Panel Layout feature on the Submit Configuration page, and you can enable it once the panel layout is built. We now inform you when the WiFi connectivity is poor or when you’re commissioning on cellular. We improved the messaging for when you fail to submit configuration.

September 28, 2023

Improvements: - You can check your PCS access from the Settings page on ProConnect. This means that you can check your access to commission PCS systems at any time, even when not on-site. - We’ve added voltage readings of the Hub+ on the commissioning report. - We have a new scanning software to scan microinverter serial numbers. Bug fixes: -Previously, the Firmware Management sometimes prompted you to download FW packages even when they were up-to-date. This issue has now been fixed. - We made some improvements to the SunVault pre-commissioning tasklist. - When updating the grid profile fails and you retry, there was no loading UI on the app. We’ve now resolved this issue so you’re aware when the retry is in progress.