EL tools: Circuit Calculator

EL tools: Circuit Calculator

Quick calcs for circuit design

0 ratings
Free

Rating summary

Details

Released
September 23, 2026
Updated
November 3, 2026

Features

EL tools: Circuit Calculator screenshot #1 for iPhone
EL tools: Circuit Calculator screenshot #2 for iPhone
EL tools: Circuit Calculator screenshot #3 for iPhone
EL tools: Circuit Calculator screenshot #4 for iPhone
EL tools: Circuit Calculator screenshot #5 for iPhone
EL tools: Circuit Calculator screenshot #6 for iPhone
EL tools: Circuit Calculator screenshot #7 for iPhone
EL tools: Circuit Calculator screenshot #8 for iPhone
iphone
ipad
🖼️Get Icon
Icons↘︎

About

All the everyday calculations for electrical design, in one app. When you're designing a circuit, small questions keep coming up: "Will this resistor pair give me the voltage I need?" "What's the rise time of this RC circuit?" "What do three resistors in parallel add up to?" "Where is the cutoff frequency of this filter?" "Which resistors give this amplifier a gain of 10?" "What resistor do I need for 10 mA through this LED?" "What value is this resistor with these color bands?" "What is 0x3F8 in binary?" Too small to open a spreadsheet, but you want the answer right now. EL tools is a practical calculator for electrical design that lets you check these things quickly on your phone. ■ Voltage Divider Enter the input voltage and target output voltage, choose a standard resistor series (E6/E12/E24/E48), and instantly find the R1/R2 combinations closest to your target. The min/typ/max output voltage is shown for each combination, taking resistor tolerance (and input voltage tolerance) into account. Useful for power supplies, voltage references, and ADC inputs. ■ RC Step Response Calculate the time constant τ = RC from the resistance and capacitance. View the rise (charge) or fall (discharge) curve as a graph, and check the voltage at any elapsed time with a slider. Handy for reset, delay, and smoothing circuits. ■ Combined Resistance and Capacitance Supports series and parallel connections. Calculate the nominal, minimum, and maximum combined value from up to three resistors or capacitors and their tolerances. ■ Filters Supports low-pass (RC/RLC), high-pass (RC/RLC), band-pass (RLC), and pi (CLC) filters. See the cutoff frequency, damping ratio, or the band-pass center frequency, Q, and bandwidth, with the frequency response shown as a Bode plot. Check a pi filter from its values, or design a 3rd-order Butterworth pi filter from a target cutoff and resistance. ■ Op-Amp Gain Choose an inverting or non-inverting amplifier, enter the target gain, and find the closest Rf/Rg combinations from a standard resistor series (E6/E12/E24/E48). The min/typ/max gain is shown for each combination, taking resistor tolerance into account. ■ LED Current-Limiting Resistor Get a standard resistor value from the supply voltage, LED color or Vf, target current, and number of LEDs in series. See the min/typ/max current with tolerances, the resistor power, and a suggested rating. If the supply is too low, the app tells you how many LEDs it can drive and the voltage you need. ■ Parts Read resistor color codes (4 or 5 bands), or look up the colors for a value. Decode chip resistor markings (3-digit, 4-digit, R notation, EIA-96), and check a chip size table with metric and inch codes, dimensions, and typical power ratings. ■ Programmer Calculator Convert values between HEX, DEC, OCT, and BIN at a glance. Tap individual bits to toggle them, and choose the word size (8/16/32/64-bit) and signed (two's complement) or unsigned. Run bitwise operations (AND, OR, XOR, NAND, NOR, NOT, shifts, rotates) and arithmetic, then feed the result back in to keep going. ■ Useful for - Checking values while designing circuits - Choosing resistor and capacitor values - Designing voltage dividers for power circuits - Checking RC delay times and filter cutoff frequencies - Choosing gain resistors for op-amp circuits - Choosing current-limiting resistors for LEDs - Identifying the resistors on your bench - Working with register values and bit masks in firmware - Electronics hobby projects and learning circuits Quick answers for those "let me just calculate this" moments. Not complex enough for a full simulation, but you still want the result on the spot. EL tools supports your day-to-day electrical design work with simple, straightforward controls.
Show more

What's New in EL tools

1.4

November 3, 2026

- New: LED Resistor. Get a standard resistor value from the supply, Vf, current, and number of LEDs, with min/typ/max current and resistor power. - New: Parts. Read resistor color codes and chip resistor markings, and look up chip sizes. - Filters: added high-pass, band-pass, and pi filters. Design a pi filter from a target cutoff. - Combined: now calculates capacitors as well as resistors. - Circuit diagrams and formulas on the Divider, Transient, Combined, Filter, and LED tabs. - The tab bar now scrolls sideways to fit all 8 tools.

More

Developer apps