
Hewer Trade Toolkit
Layout & Material Calculators
0 ratings
Free
About
Lay it out before you cut.
Hewer Trade Toolkit gives you the layout math a finish carpenter does on a scrap of drywall: in your pocket, to the sixteenth, with a drawing you can hand to the client.
Pick your trade and your tools come first. Finish Carpentry is live with twelve tools:
• Accent Wall Editor: draw any wall shape (rakes, gables, cutouts), lay out board & batten, slats, grids, tartan or diamond, and get a cut list.
• Tape Calculator: add, subtract, multiply and divide feet, inches and sixteenths, the way you read a tape. One tap halves it for the center; Equal spaces splits it into any number of spaces and lists every mark.
• Angle Finder: hold your phone against each wall and it reads the corner and the miter, then hands it to Miter & Crown. It also reads a surface's slope.
• Shelf Spacing: equal gaps in any opening, with marks from the floor or the ceiling.
• Coffered Ceiling: beam layout, on-center marks and total beam run.
• Wainscoting · Picture Frame: set the chair rail height and get the wainscot boxes, reveals, marks and molding footage.
• Board & Batten: wainscot battens under a top rail: set the rail height and get the spacing, batten length, marks and boards to buy.
• Baluster Spacing: how many balusters so a 4″ sphere can't pass, the exact gap, and a mark for each, on a level or stair rail.
• Plywood Cut List: list your parts, pick the sheet (4×8, 4×10, 5×5, 5×10, 5×12), and get how many sheets to buy and where every part goes, ripped into strips and crosscut the way a table saw cuts.
• Wall Layout & Material Estimator: walls in, doors and windows out, then boards and sheets with waste.
• Miter & Crown: flat trim (base, casing, frames and bay windows) or crown at any corner: the miter, the bevel, which way each piece swings, laid flat or nested, plus the layout line.
• Stairs: riser and tread to 1/16″ from the total rise, stringer length, framing-square settings, a mark for every step along the stringer, the skirt board and its plumb and level cuts, and residential code checks.
Plumbing is live with two tools:
• Pipe Offset: travel, run and the pipe to cut for an 11¼°, 22½°, 45° or 60° offset, including rolling offsets.
• Drain Slope: the fall over a run at ⅛″ or ¼″ per foot, what a 2′, 4′ or 6′ level shows, and the fall at each hanger. Or check a run you measured against the minimum for the pipe size.
Electrical is live with three tools:
• Conduit Bending: offsets, 90° stub-ups and three-point saddles, with every mark measured from the end of the conduit and the exact shrink.
• Wire Size: the smallest copper or aluminum wire for the amps and the length of the run, single or three phase, and whether the amps or the voltage drop set it. Ampacities from NEC 2023 (verify with your inspector).
• Box Fill: count the wires, devices and grounds, and get the cubic inches the box must hold, the smallest common box that holds them, and a pass or fail for your box, including plastic boxes by their marked volume.
Every layout exports to a PDF with the drawing, the dimensions, the cut list and the material list. Share it by text or email, or save it to Files.
Works with no signal: in a basement, on a roof, in airplane mode. Projects save on your phone. No account and no login.
Feet and inches, inches with fractions, decimal inches, or metric. English, Spanish or Russian.
Missing a tool? Tap Request a tool, tell us what you measure or lay out, and we'll build the next ones from what you ask for.
Every tool is free. No account, no sign-in and nothing to buy.
Show more
+2
What's New in Hewer Trade Toolkit
1.0.3
November 18, 2026
• Now works on iPad, with the layout and drawing side by side. • Bluetooth tape: the box you tap glows and waits. Measure and it fills, then the next box waits. The tape reconnects by itself. • Tap any size on a drawing to set it. • Type lengths in feet and inches. • Clearer answers and bigger buttons. • Accuracy fixes: tile, concrete rebar, wall and roof material counts, and metric entry.
More






