Audio Toolbox vs GtrEQ

Audio Toolbox is a suite of audio analysis tools for the iPhone and iPad. It comprises both audio waveform generators as well as a highly accurate Fast Fourier analysis engine, an audio oscilloscope and various frequency detection and tuning tools. The Tone Generator allows you to create anything from a simple sine, triangle, square, or sawtooth waveform as well as white and pink noise. It also supports log and linear sweep tones with definable range and level and complex wave construction using sine waves. The later is great for teaching audio theory with its DTMF and complex tone generation tools you can build complex waveforms and then analyse their component parts using FFT and the oscilloscope. Build DTMF, triangle, square or saw waves using multiple sine waves etc. The Audio Oscilloscope allows you to analyse directly from the tone generator or microphone. The scope features both free running and single shot modes with adjustable triggering options. The single shot mode automatically starts and stops capturing when short bursts of sound exceed a threshold. The oscilloscope also features a simple measuring tool to help measure duration and frequency of a waveform. The FFT Analysis section provides both Linear, Logarithmic as well as 1:1, 1:3 and 1:6 Octave modes. There is also an SPL meter complete with LEQ options and A/C weighting, log and linear Spectrograph and Mixer EQ modes for setting up audio mixers. All screens support 10x zoom, full screen and pause modes to aid analysis. There are also specific modes to detect peak frequencies, musical notes with cents offset, perfect for instrument tuning. Definable calibration tuning allows you to tune +/- 40Hz. Features: •20Hz-22KHz Tone Generator. •Sine, Square, Saw, Triangle, Sweep and MultiTone options. •Accurate 8K Fast Fourier Analysis. •32bit / 44KHz floating point audio sampling. •Standard ANSI/IEC A and C weighting curves. •Up to 64x oversampling. •Smoothing (alternative to averaging). •Automatic noise cancellation. •Automatic peak note / frequency and octave display. •Narrow band Linear and Logarithmic scalable displays. •Spectrogram display with Log and Linear Modes. •1:1, 1:3 and 1:6 octave display modes. •1:1, 1:3 and 1.6 Mixer tuning modes. •SPL (Sound Pressure Level) display. •Max, Min and Peak level capture. •LEQ Mode (Equivalent Continuous Sound Level). •Variable definable decibel scales. •Touch screen display of nearest point with frequency and decibel readout. •Audio Oscilloscope - Free Running and One Shot modes. •0.1 to 1000Hz timebase. •0.25-50x scope Magnification. •Definable trigger (leading and trailing edge). •10x zoom and full screen modes. •Pause facility freezes the live trace to aid analysis of data. •Camera Roll capture facility. •Export and Email CSV data from FFT or Scope. •Built in web server for transferring files. •Capture peaks over time facility. •Works on both iPhone and iPads.

GtrEQ Guitar EQ & Buzz Kill (AUv3) GtrEQ is an audio effect plugin that can run standalone, or in any AU compatible host application such as Logic Pro or GarageBand. Overview GtrEQ is a 5-band EQ / tone-shaping effect made specifically for guitar players, with the 5 bands focused across the frequency spectrum where the guitar typically lives. The peak / resonance of each band is also more gentle compared to general-purpose EQs, so adjacent bands are very "interactive". This makes GtrEQ well suited for overall guitar tone "sculpting", as opposed to the surgical precision needed for targeting specific frequencies. GtrEQ also includes an optional "Buzz Kill" filter to help reduce mains hum noise. This buzzing can be a problem sometimes with single coil pickup guitars. Depending on your situation, GtrEQ might not be able to kill the buzz completely, but it should help reduce it significantly without impacting your original guitar tone too much. Controls Buzz Kill - Sets the target frequency of the mains hum noise filters which will depend on where you are in the world. For example, UK is 50Hz and US is 60Hz. Setting the control to Off will bypass the mains hum filters entirely. Reduction - Sets how much attenuation is applied to the mains hum noise. Ideally, you want to set this control so the noise is no longer noticeable, or is at least at a "manageable" level. Buzz Kill processing has been designed so that the original guitar signal is impacted as little as possible, but you may notice a less "full" guitar tone when the Reduction amount is at maximum. Buzz Kill processing, when enabled, occurs before the EQ section. EQ - Switches the EQ On or Off. This is a "soft switch" so is well suited for automation / MIDI CC control if your host supports it. EQ Bands - Sets a +/-12dB boost or cut for each of the labelled frequency bands. You can think of each band as affecting bass, low mids, high mids, treble and presence, but because of their interactivity, they don't work independently. You might be surprised by the range of tones you can get with just five bands! Out - Applies a final stage gain trim to the output at the very end of the internal signal chain, between -24dB and +12dB. Shameless plug alert... ANALOGyAMP GtrEQ partners really well with ANALOGyAMP, a retro guitar amp simulator. Placing GtrEQ before ANALOGyAMP in the signal chain allows GtrEQ to function as a boost, effectively driving the input stage of ANALOGyAMP harder. ANALOGyAMP has actually been designed to "take pedals well" albeit virtual ones! You could also use the EQ section in GtrEQ to accentuate the mid frequencies more, and roll-off the bass and treble sides in a similar way to a very famous green overdrive pedal when used primarily as a mid boost. And if you use a MIDI controller, you could potentially have four different virtual channels from two controller switch assignments, with no pops or clicks when you flip between them: SW1 - Toggle Channel Gain on ANALOGyAMP (clean / crunch for example) SW2 - Toggle EQ on GtrEQ (bypass / mid boost for example) Alternatively, place GtrEQ after ANALOGyAMP to sculpt your tone further, with an EQ specifically designed for guitar. For more info and support please visit: www.waverley-instruments.com/robjackson