MHD Flasher vs My smartLED

MHD Flasher is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! Simply download the MHD Flasher app that connects via a Wi-Fi adapter to your iOS device and your vehicle’s OBD-II port, start the app, and within 4 minutes the initial installation is complete. Further map changes are much faster - only 20 seconds! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported E-Series Vehicles: 135i, 135is, 335i and 535i 2006-2013 335is 2011-2013 Z4 35i/is 2009-2015 1M 2011-2012 X1 35i 2010-2013 X5 35i 2010-2013 X6 35i 2008-2014 Supported F/G Series Vehicles: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.

This is an LED Bluetooth lighting control software. Connect to our wireless devices. You can adjust the color of the lights as needed, such as red, green, blue, yellow, purple, cyan, white, etc. It can also adjust the brightness. You can also adjust the light change mode, such as jump, fade, strobe, etc. You can set the light voice mode, twinkle mode, Meteor mode and so on. This software is relatively simple to use, first open our Bluetooth light fixtures, make sure that the mobile phone Bluetooth is turned on, open our software, our software automatically links to our Bluetooth light fixtures. If the connection is successful, you can control the lighting effects through your phone. Thank you