MHD Flasher vs BimmerObd

MHD Flasher is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! Simply download the MHD Flasher app that connects via a Wi-Fi adapter to your iOS device and your vehicle’s OBD-II port, start the app, and within 4 minutes the initial installation is complete. Further map changes are much faster - only 20 seconds! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported E-Series Vehicles: 135i, 135is, 335i and 535i 2006-2013 335is 2011-2013 Z4 35i/is 2009-2015 1M 2011-2012 X1 35i 2010-2013 X5 35i 2010-2013 X6 35i 2008-2014 Supported F/G Series Vehicles: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.

Turn your phone into a capable car diagnostic tool. Connect a standard, compatible Wi-Fi OBD-II adapter and read what your vehicle's computer is really reporting — trouble codes, live sensor data, readiness monitors and more. WHAT YOU CAN DO - Read and clear trouble codes. Scan the engine and other control modules for current, pending and permanent diagnostic trouble codes, then clear them after a repair. - Understand every code. A built-in offline library explains what each code means, its likely causes, common symptoms, suggested fixes and a typical repair cost range. No internet connection needed. - Watch live data. Real-time engine speed, vehicle speed, coolant and intake temperature, engine load, throttle position, fuel trims, airflow, timing and more on smooth custom gauges and charts. - Check battery health. Follow charging voltage with clear resting, cranking and charging readouts. - Readiness and freeze frame. See which emissions monitors are ready before an inspection, and view the sensor snapshot captured when a fault was set. - Service resets and guides. Step-by-step guidance for common maintenance procedures. - Reports. Save any scan and export a clean PDF to share with a workshop or keep for your records. - Garage. Store several vehicles and switch between them in a tap. - Knowledge base. Plain-language articles that explain codes, monitors and how the whole system works. COMPATIBILITY Works with most vehicles that support the OBD-II standard — generally cars and light trucks sold from 1996 onward in North America, and from 2001 (petrol) or 2004 (diesel) onward in Europe. Real-time features require a compatible Wi-Fi OBD-II adapter, sold separately by third parties. Demo Mode needs no hardware at all. PRIVATE BY DESIGN Everything runs on your device. No accounts, no sign-ups, no ads and no tracking. Your vehicle data, code lookups and reports stay on your phone. A NOTE This is an independent product and is not affiliated with, endorsed by or associated with any vehicle manufacturer or adapter maker. Diagnostic information is provided for guidance only — always confirm any repair with a qualified technician. Subscription Information: . Payment will be charged to your Apple ID upon purchase confirmation. . Subscriptions automatically renew unless canceled at least 24 hours before the current period ends. . Renewal charges occur within 24 hours before the current period ends. . Manage or cancel subscriptions in your App Store account settings. . If a free trial is offered, unused portions will be forfeited upon subscription purchase. Privacy Policy: https://doc-hosting.flycricket.io/lntm-s-privacy-policy/4d4e0876-516c-428c-b630-4e9ccd29f174/privacy Terms & Conditions: https://doc-hosting.flycricket.io/lntm-s-terms-conditions/635273cf-17ef-4330-ba8b-00940c49d9eb/terms