BWC5 vs HVAC Tools PT Chart

BWC5 - application for heating controllers Buderus Logamatic 5000. It's used for monitoring and control heating system from smartphone or tablet. Functions: - Display boiler information - Display fault messages - Display data from FM-CM module - Display data from FM-AM module - Display of heating circuit information - Display of hot water circuit information - Change heating circuit mode (Day/Night or Automatic/Manual) - Change the room's set temperature - Change hot water mode (Day/Night or Automatic/Manual) - Change hot water set temperature - Change FM-AM module mode and temperature setpoints Features: - Quick access to control system parameters from your local network - Show controller settings without SMS and registration - Don't required connect to Buderus Commercial Center Connection: First, you'll need connect Buderus Logamatic to your local network and find IP address. Second, for LAN1 controller settings select connection type - Modbus TCP/IP, Modbus - w/o HeartBeat. Attention! If you select this types you can't use Buderus Control Center. After all, start application, enter system IP address and connect to controller. If you need remote control you can set up your router, for example VPN connection to your local network. System requirements: - Buderus Logamatic 5000 (version from 1.4.7) - LAN/WLAN router Supported devices: - Buderus Logamatic 5311 - Buderus Logamatic 5313 - Bosch Control 8000 For more information, please visit our website: www.techno-line.info

Gauge is a field toolkit for HVAC and refrigeration technicians: a pressure-temperature chart for 10 refrigerants, superheat and subcooling calculators, troubleshooting checklists and a service call log with PDF reports. PT CHART - R-410A and R-22 free; R-134a, R-407C, R-404A, R-32, R-454B, R-290, R-438A and R-422D with Pro - Look up the saturation temperature for a pressure, or the pressure for a temperature - Scroll the full table from -40°F, with safety notes for the A2L (R-32, R-454B) and A3 (R-290) refrigerants CALCULATORS - Superheat: suction pressure and suction line temperature give the saturation temperature and the superheat - Subcooling: liquid line pressure and liquid line temperature - Temperature split: return and supply air - Ohm's Law: enter any two of volts, amps, ohms and watts - Pro: airflow (required CFM from BTU/h or tons and the temperature split), duct sizing (round and rectangular sizes from CFM and air velocity), capacitor check (measured against rated µF) and voltage drop (copper wire by AWG, one-way length, amps and supply voltage) Superheat, subcooling, temperature split, capacitor and voltage drop results are color-coded against typical ranges, with what to check next. SERVICE CALL LOG - Customer or address, complaint, system type, make and model - Suction and liquid pressure, superheat, subcooling, suction line, liquid line, supply and return air temperatures, compressor amps - Your diagnosis, the work performed, refrigerant type and amount, parts, notes, cost and time on the job - Free: up to 10 service calls. Pro: unlimited calls, search, and a PDF service report with your name and certification that you can share with the customer REFERENCE - Step-by-step checklists: AC not cooling (free), furnace not heating and heat pump not heating (Pro) - Typical ranges for superheat, subcooling, temperature split and compressor amps - Refrigerant facts: GWP, A2L or A3 safety class and phase-down status - System types, a copper wire ampacity table and an EPA 608 overview (certification types and key rules) AI ADVISOR (PRO) Describe a symptom or a set of readings and get a short written answer from an AI model. It sends only the message you type and needs an internet connection. AI answers can be wrong: check them against your own readings and the equipment manufacturer's data. GOOD TO KNOW - Gauge works in US units: °F, psig, CFM, inches, feet, AWG and pounds - The PT chart, calculators, reference and service log work without a connection GAUGE PRO Free: the PT chart for R-410A and R-22, the superheat, subcooling, temperature split and Ohm's Law calculators, up to 10 service calls, the AC checklist and the reference tables. Pro adds the other 8 refrigerants, the airflow, duct sizing, capacitor and voltage drop calculators, unlimited service calls with search and PDF reports, the furnace and heat pump checklists and the AI Advisor. In the US, Gauge Pro is $4.99 a month or $39.99 a year (US prices; other countries see their own price in the app). Subscriptions renew automatically unless cancelled at least 24 hours before the end of the period. Manage them in your App Store account settings. Terms of Use (EULA): https://www.apple.com/legal/internet-services/itunes/dev/stdeula/