Modulo Calculator vs ゆびタイマー：スピードキューブ計測

Modulo Calculator has a remainder calculation function that is convenient for dispensing work in pharmacies, shipping work in distribution warehouses and calculation of the number of patterns and the number of remaining stitches in knitting, etc. Two input numbers and the result after calculation are shown so that the user can check input numbers with the result, therefore, the accuracy of calculation is greatly improved. It has the set memory in addition to the general independent memory. The set memory automatically memorizes calculation history of all sets of calculated input numbers, an arithmetic operator and a result number. (Instructions) - When performing division by pressing [MOD] instead of [÷] to calculate, the quotient and remainder will be displayed. The remainder is calculated so that it is greater than or equal to 0. - For example, when calculating the quotient and remainder of 30 ÷ 7, if you operate [3] [0] [MOD] [7] [=], the calculation result "4-2”, which means the quotient is 4 and the remainder is 2, will be displayed on the result display. - For example in a dispensing work, a calculation when counting 3 tablets a day and 90 days with 14 tablets per sheet is [3] [×] [9] [0] [MOD] [1] [4] [=], the result “19-4”, which means 19 sheets and 4 tablets, is displayed. And ”270"(tablets) from 3×90 keeps displayed at 1st display and “14"(tablets per sheet) keeps displayed at 2nd display. So input numbers and the result can be checked at a glance. - If the result of calculation with the [MOD] key is used for the next calculation, the value of the quotient will be used. - It is easy to calculate by changing one input number after a calculation. For example after a remainder calculation, in the case you would like to change the tablet number per sheet of 2nd input number, tap the 2nd input number and input a new number and tap the result display(or tap [=]) to finish the calculation. - To recall calculation history, tap [＜ Prev] key until you find the history you want. After you tapped [＜ Prev] key, if you want to recall a newer history, tap [Next ＞] key until you find it. - To clear the calculator completely including calculation history, close Modulo Calculator. - To clear the calculator except for the set memory and the independent memory on MR-line, tap [C] key and then tap [AC] key appeared, that is, double tap [C] key. - To clear the independent memory on MR-line, tap MR key and then tap MC key appeared, or swipe on MR-line. - To completely clear the number you have just input on 1st-line or 2nd-line, tap C key. - To erase a right end number at 1st-line or 2nd-line framed in the input mode, swipe on the line. - When using the [M+] key or [M-] key to calculate the remainder, only the quotient will be used for the memory calculation. (Others) - The calculation range is −999,999,999,999 ~ 999,999,999,999. - The maximum number of digits is 12. - The developer assumes no responsibility for any loss or claims by third parties which may arise from the use of this app. Modulo Calculator Ⓒ 2020 Takao Ichimura

「ゆびタイマー」は、ルービックキューブのスピードキューブ用タイマーです。iPhone を横に置き、画面をスタックマットの代わりに使います。 画面の左下と右下に、手の形のパッドがあります。両手をパッドに置くと赤いランプが点き、少し待つと緑に変わります。緑になってから手を離すと計測が始まり、そろえ終わったら画面に触れれば止まります。片手だけでは始まらないので、キューブを持ち直す手が画面に当たっても安心です。 ■ スクランブル 2x2、3x3、4x4 のスクランブル（計測の前にキューブを崩す手順）を、画面下の帯に毎回出します。タップすれば別の並びに替えられ、「？」から記号の読み方を確かめられます。 ■ 平均と記録 直近5回の平均（ao5）、12回（ao12）、100回（ao100）を、大会と同じ数え方（最も速い記録と遅い記録を除く）で出します。記録はパズルごとに分けて残り、あとから +2 や DNF を付けたり、消したりできます。 ■ 15秒の観察（インスペクション） 設定で有効にすると、両手をパッドに置いて離したところから15秒の観察時間を数えます。15秒を超えると +2、17秒を超えると DNF が自動で付きます。 ■ 計測に集中できる画面 計測中はタイムとランプと手のパッド以外の表示が消え、画面のどこに触れても止まります。計測中に画面が暗くなることもありません。 登録やログインは要りません。記録はこの iPhone の中だけに保存されます。本体は無料で、画面の上に広告が出ます（計測中は消えます）。