Fundamental2 vs Binarhythmic Rhythm Generator

Fundamental is a sound synthesis software combining the different roots of electronic music history. Its wave engine is a faithful sonic recreation of a vintage Rohde&Schwartz vacuum tube oscillator ( having been widely used at WDR by Stockhausen ) Thanks to sonicLAB audio engine design, Fundamental leaves behind the limitations of the original device by proposing complex modulation possibilities, stochastic distributions addressing the sonic parameters like frequency , gain, stereo panning etc. in continuum, which has not been applicable until now. The Fundamental software presents you 8 instances of this vintage sine wave generator with all the artifacts and richness of a vintage equipment. That combination is we believe something you should experience. Direct Link for manual : https://www.sonic-lab.com/Fundamental/Fundamental2iOS_manual.pdf Fundamental2 brings following new features to the Fundamental1, basically now you can create organic, endless moving textures. (for iOS standalone and AUv3 ) - Ring Modulator, 7 individual modulator oscillators and one carrier oscillator. - A morphing engine which lets you gradually morph between four instances of Fundamental scenes. Also a stochastic manipulation on the 2D morphing panel is possible. - True real time gradual transition between tuning scales. - Rotary Encoder midi controller mapping for high resolution oscillator frequency and gain control with midi hardware. - One can send midi note-on messages to each Fundamental oscillator on discrete midi channels. - A morse code simulator is available on each GEN (sonicLAB LFO design ) which can create custom morse signals to modulate the relevant GEN outputs. - new envelope type "Ernd". Whether you play live electronics, compose for media or just insterested in early electronic music, Fundamental2 is a strong tool. Some of the main features of Fundamental1: ( iOS standalone and AUv3 ) - unique polymorphing wavetable synthesis without any compromise in data content and precision. - 4 dynamic wavetables being rendered for each voice to represent infinitesimal steps of frequency and gain combinations between 1HZ – 3800Hz of the original vacuum tube oscillator. - 8 simultaneous voices each with custom freq, gain, boost, panning and modulation settings. - Custom or harmonic frequency distribution of voices with variable spread ratio and tuning table. - 4 independent stochastic modulations for each voice (32 in total) addressing all parameters with various continuous, discrete distributions and also standard waveforms. - Full MPE support with various configuration possibilites. - Independent Attack / Release envelopes for each voice with various modes, AR times can be set to degrees of randomness. - Vintage oscillator or pure sine wave mode. Recommended iPAD model : A12 processor or higher. Due to screen size challenges, iPAD Mini models are not recommended.

Binarhythmic is a MIDI sequencer that would generate rhythmic outputs based on the binary numbers. The sequencer has a counter, increasing on each sequencer cycle. The binary form of this number, something like "010110011".  Each 0 or 1 is a "Bit", and each bit is a MIDI output. If a bit is 1 then the gate is open for that bit, and if it's 0 then the gate is closed for that bit.  You can use the Multiplier parameter for controlling the sequencer counter.  The rate parameter controls the sequencer speed. Each bit has a note, velocity, gate length, trigger type and logic operation.  You can also vary the velocity and gate length. With the lower amounts of variety, you can humanise the sounds like Hi-Hats.  You can assign different MIDI channels to the bits and control different synths. The gate type is a very important parameter for the rhythm generation. On each sequencer cycle, if the gate is open for a bit; - Rest mode doesn't send the MIDI. - Single mode sends the MIDI once for the first sequencer cycle when the gate is opened. - Multiple mode sends the MIDI on each sequencer cycle while the gate is opened. - Hold mode sends the MIDI when the gate is opened and sustains it until the gate is closed Logic is one of the most powerful features of Binarhythmic. You can create endless rhythmic possibilities by using the logic operations. You can modulate the bits by applying logic operations on them with the other bits. - AND(&) operation opens the gate if the bit's gate is open AND the other bit's gate is open. - OR(+) operation opens the gate if the bit's gate is open OR the other bit's gate is open. - XOR(^) operation opens the gate if the other bit's gate is NOT open. With the randomizer you can randomize the notes on your bits in a range of notes that you can set. Or you can hand-pick the allowed notes from the list. With that feature, you can fully control the randomizer. In the "Random" mode, you can assign the randomization chance of the bits. When select the Random mode, the new Config button on the bottom toolbar appears and you can configure the randomizer. You can also access this configuration menu from the settings menu as well. In the multiple gate type mode, you can set the randomizer behaviour from the settings menu. If you toggle the "Randomize notes on each sequencer cycle" setting, then the randomizer will generate a new note on each sequencer cycle while the gate is open, if the gate type is multiple. Otherwise, it will randomize the note on the first sequencer cycle when the gate is opened and will trigger that note on each sequencer cycle until the gate is closed. Binarhythmic app runs as standalone app as well as AUv3 MIDI Plugin. You can create AU presets and use AU parameters of the AUv3 plugin. You can control or even automate every AU parameter of Binarhythmic.  You can modulate the multiplier parameter with PatternBud. You can also control the key and scale with BrainBud. Binarhythmic is a MIDI app and does not produce any sound on its own. You need to route its MIDI output to an audio app. For using the AUv3 plugin, you need an AUv3 host app such as AUM, Cubasis, Nanostudio, Loopy Pro etc.