livetoolkit vs Home Theater SPL

Everybody working in the live concert business has experienced situations like this: You've just arrived at the venue. According to the local promoter everything should have been put up before you arrived, but it hasn't. Now it'll take an hour or more to set up the PA-System and Lighting-gear before you can start to do your actual work. All has to be done as fast as possible. You don't have time to get your laptop out of the car and working just to do some necessary calculations. Now you can just take your iPhone®, iPod touch® or iPad® and start doing your calculations with LiveToolkit. LiveToolkit helps audio technicians to make relevant calculations directly with his or her iPhone®, iPod touch® or iPad®, like: • Delay times for your PA-system: Conversion between time and distance. • Stacking distance of your subs: Conversion between frequency and wavelength. • Getting your PA-Settings into the controller: Conversion from Q-Factor to Bandwidth and back. • Setting up your controller: Limiter calculations depending on speaker capacity and amp output. • Getting the musicians tempo: Tap Tempo calculation with different note weightings. LiveToolkit helps lighting technicians to make relevant calculations directly with his or her iPhone®, iPod touch® or iPad®, like: • Getting the start address for multiple fixtures based on quantity, channels, and first address used. • Setting the DMX-address right using a DIP-Switch, or identifying the address value of a DIP-Switch. LiveToolkit helps any technicians to make relevant calculations directly with his or her iPhone®, iPod touch® or iPad®, like: • Universal useful conversion between feet and meter and lbs to kg. • Conversion between Watt, Ampere and Volt. • Calculate the voltage drop in your cable based on length and profile. • Trigonometric calculation on heights based on angle & distance. IMPORTANT NOTES: • Although good tested - this application remain a piece of Software: rockbaby engineering will not take any responsibility for any issues that may occur using LiveToolkit.

Home Theater SPL Information   Professionals use SPL meters to calibrate audio reproduction systems in cinemas, so why shouldn’t Home Theaters or Home Cinemas owners use them too? Now the very same SPL meter that’s in our TestCard ProHD app is available separately.   An SPL or “decibel” meter is an essential tool when setting up surround sound systems.   Home Theater SPL a solution for calibrating the audio level of surround sound systems within the home without the need for additional equipment. Our app TestCard ProHD is the innovative means to calibrating your screen and audio to ensure a consistent and correct representation of display media and surround sound and includes an SPL meter. If you wish to calibrate both audio and visual aspects of your Home Theater then please consider TestCard ProHD.   Surround Sound Level Setting.   An SPL, or “Decibel” meter, is a sound power meter to assist with setting the speaker levels.   As speakers have different sensitivities they produce different levels of audio.   One may be louder or quieter than another, and how the room is laid out will also have an effect, but the goal is to have similar levels from all speakers reaching the viewing position.   To create that “centered sound stage” it’s important to calibrate the system.   While an approximation may be possible by ear, it is best done with an SPL meter.   A second factor to consider is simply that it also verifies that each speaker is in the correct position!   While working on an initial installation it is imperative to verify that audio is emanating from the selected speaker.   Select SPL on the main screen of Home Theater SPL to launch the meter.   Turn the iPhone or iPad so that the bottom microphone is pointing upwards and hold at ear level.   The scale is fixed, and the main black needle gives a slow average response as desired.   A red needle is provided for peak noise level information and is not required during calibration. Start with the front left speaker and allow it to set the benchmark level; the target for all other speakers to be set to.   Typically the audio will be in the 70-80dB range and as a guide 70dB is marked in red on dial.   With Home Theater SPL it is possible to note the current sound level by tapping on respective speaker, making it easier to recall where individual speakers were.   Move to the center speaker and adjust its level to closely match the first.   It is normal for amplifiers to increase or decrease sound levels by 1dB increments and it may not be possible to get an exact match.   Move to the next speaker in the list and repeat.   Variance of 1 or 2dB during calibration is normal, but it will settle around a value.   Some systems will have 5 speakers and some will also have the LFE, or bass effects, speaker to give the “0.1” to make 5.1 audio.   With the SPL meter there are 7 main speakers shown with one LFE to make 7.1.   With a 5.1 system the Mid speakers will not be present and therefore can be skipped. To check it’s always advisable to run round checking the speaker levels again, perhaps even adjusting the initial left speaker if it was not possible to set others within the range allowed by the amplifier.   When complete ensure that you save the settings within the amplifier if they’re not automatically saved.   For reference a screen shot of the SPL meter on Home Theater SPL can be taken to record any stored audio level by pressing the camera button.