iSlipstick RF vs ST25DV

iSlipstick RF iSlipstick RF contains all of the functionality of the standard iSlipstick plus many functions specifically for RF work. RF Calculators included with iSlipstick RF are: PATH LOSS – Enter all of the RF link parameters such as transmitter output power, antenna gain, cable loss, distance and frequency to find the actual RF level at the receiver. MICROWAVE DISH BEAMWIDTH & GAIN – Enter the dish size, frequency and efficiency to find the 3 dB beamwidth and antenna gain. WAVELENGTH – Metric & U.S. RETURN LOSS / VSWR – Enter forward and reflected power to find VSWR, reflection coefficient and return loss. FRESNEL ZONE – Enter link distance, obstacle distance and frequency to find the 60% and 80% zone radii. This calculator also provides a visual display of ground clearance. VELOCITY FACTOR (VOP) – Enter the dielectric constant of a coax to find the Velocity of Propagation and enter the cable length to find the propagation delay. This calculator can also find the necessary cable length for a given delay and VOP. INTERMODULATION – Enter up to six frequencies to find the 2nd, 3rd, 5th and 7th intermod products that can be created. A 'hit' window can be set to eliminate out of band results. I.F. FREQUENCY – Enter the incoming carrier frequency and 1st local oscillator frequency to find the resulting I.F. and whether the spectrum is inverted or normal. This is a great calculator when working with up/down converters. INTERCEPT POINT – Once you have determined the levels of fundamental and intermodulation tones in a system, you can enter those values into this calculator to find either IP2 or IP3. Standard Calculators included in iSlipstick RF are: OHM'S LAW – Find voltage, current, resistance and power. REACTANCE – Find inductive and capacitive reactance by entering frequency and capacitance or inductance. RESONANCE – Find the resonant frequency of an inductor – capacitor pair. VOLTAGE DIVIDER – Enter the voltage into a resistor divider network to find the output voltage. PARALLEL RESISTOR – Enter up to six resistor values to find the resultant parallel resistance. SERIES and PARALLEL RLC – Enter R, C and L of a series or parallel circuit to find the impedance and phase angle. OP-AMP – Find the gain of either an inverting or non-inverting op-amp circuit. TIME CONSTANT - Find the first 5 time constants of both RC and RL circuits. Standard Converters included in iSlipstick RF are: RESISTOR COLOR CODE – Enter a resistor value to find the color code or enter the color code to find the resistor value. SMD RESISTOR – Enter 3 digit or 4 digit SMD codes to find the resistance value. Also does EIA-96 conversion. VOLTAGE CONVERTER – Convert between RMS, average, peak and p-p values. dB CONVERTER – Convert dBm, dBV, dBW and dBuV to absolute values and vice-versa in 50, 75 and 600 ohm load. TEMPERATURE – Convert between four popular scales. PERIOD – FREQUENCY – Convert waveform period to frequency and vice-versa. LENGTH, AREA, VOLUME, CAPACITY and WEIGHT – Convert from metric to U.S. and vice-versa. Also convert within same standard. A help page is also available as a quick function guide. Tested with iOS 12.0 thru iOS 15.1

The ST25DV-I2C CryptoDemo iOS application shows how to establish a secure transfer channel over NFC, between an STM32 microcontroller and an iOS smartphone using coreNFC framework. It uses the fast transfer mode (FTM) feature of the ST25DV-I2C NFC Tag. An ST25DV-I2C-DISCO board is required to run the demonstration. This demonstration establishes a secure transfer channel by using cryptography to perform mutual authentication and to encrypt the communications over NFC. This secure transfer channel is used during the demonstration to securely send and retrieve data, perform the device settings, and upload new firmware. Only the granted user may communicate with the STM32 microcontroller to perform these operations. All the communications are encrypted between the microcontroller and the iOS phone in both ways, so that the user can configure the product or retrieve data securely. FEATURES : - Use the new NFC core feature of iOS 13, supporting the read an write of NFC for ISO15693 tag protocol. - Encryption of all NFC bidirectional communications between an iOS Phone and an STM32 microcontroller Fast communications over NFC, using ST25DV fast transfer mode - AES and ECC cryptography - Mutual authentication between the iOS phone and the STM32 microcontroller - Establishment of a unique AES session key - Encryption can be used to retrieve data, set device settings or update the firmware securely