Comparison

Span Calc vs Roof Guide

Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.

Head to head
About

Span Calc

Calculate maximum horizontal spans for wood joists and rafters using various lumber species and grades. Compares multiple options for common loading conditions based on NDS® standards.

Highlights
  • Calculates joist and rafter spans
  • Supports all softwood and hardwood lumber
  • Uses 2021 NDS® for Wood Construction
  • Compares multiple species and grades
  • Handles common loading conditions
Features
Read full description

The American Wood Council (AWC) Span Calculator for Wood Joists and Rafters (Span Calc) performs calculations for all species and grades of commercially available softwood and hardwood lumber as found in the 2021 National Design Specification® (NDS®) for Wood Construction. Joists and rafter spans for common loading conditions can be determined. A span options calculator allows selection of multiple species and grades for comparison purposes. Supported by the Softwood Lumber Board. Maximum horizontal spans for joists and rafters are calculated based on the following assumptions and conditions: · Joists and rafters are oriented to support vertical loads applied to the narrow (1.5 in. thick) face of the member, resulting in strong-axis bending. · At least three joists or rafters are installed parallel to one another and spaced not more than 24 inches on-center, with properly designed sheathing attached on the top (compression) edge of each joist or rafter. · Joists and rafters are single-span with adequate structural support at each end. The Span Calculator does not address cantilevered joists and rafters, multiple-span joists and rafters, or spliced joists and rafters. · For joists and rafters, most building codes specify a minimum bearing length of 1.5 inches on wood or metal and not less than 3 inches on masonry or concrete. These minimum bearing lengths are to be used in the absence of calculated bearing lengths. Consult the local building code for specific requirements. · Joists and rafters carry only combinations of dead load plus live load (D + L), dead load plus snow load (D + S), or dead load plus roof live load (D + Lr). The Span Calculator does not address wind load or seismic load. · Buildings in regions with ground snow loads greater than 70 psf should not use the prescriptive provisions of the governing building code without approval of the authority having jurisdiction. Buildings in these high snow zones should be designed in accordance with accepted engineering practice. While every effort has been made to insure the accuracy of the information presented, and special effort has been made to assure that the information reflects the state-of-the-art, neither the American Wood Council nor its members assume any responsibility for any particular design prepared from this Span Calculator application. Those using this Span Calculator assume all liability from its use.

About

Roof Guide

This app provides a comprehensive suite of calculators for roofing, framing, decking, stair construction, and concrete work. It helps construction professionals estimate quantities, costs, and perform complex calculations with ease, supporting both US and metric measurements.

Highlights
  • Roof framing calculations
  • Decking and flooring estimation
  • Stud wall setout and costing
  • Stair framing calculations
  • Concrete volume and cost estimator
  • Unit conversion (metric/imperial)
Features
Read full description

Roofing and framing carpentry calculator, decking, stairs, concrete, stud wall calculators. In addition to the roof calculators the decking / flooring, stud wall and concrete calculators also estimate quantities and costs. US or metric measurements. Developed by a carpenter and builder, used by carpenters, roofers, contractors, builders and construction pros in over 40 countries around the world. Roof Guide (previously Roofers Guide) is not a 'How to App’ - you know how! It is designed to save you the time and effort required for roof, framing, deck, stairs & other building / construction calculations Accurate, reliable and easy to use, it is an indispensable tool for the construction pro. Metric or Imperial (feet, inches and fractions of an inch (or decimal) Print, email or reports. Never forget your span or rafter tables, red roofing book and other standalone construction calculators again! CALCULATIONS INCLUDE: ROOF FRAMING:- - Rafter,Hip/Valley Lengths - Multiple cut angles, including for compound saw - Template (adjustable) sizes for the same cuts - where used - Setout of Creepers/Jack Rafters(US), ridge and wall - Roof Pitch Factor degrees, inches (US), D:M:S - Rise : Run ratio - Birdsmouth calculations - Drop or Chamfer Hip adjustments - Multiple heights measures, including:- top/bottom of ridge, roof centre, - Hypotenuse calculations eg: Calculate Pitch from ridge rise - Adjust pitching plate heights where one wall is higher eg Bulkheads - Ridge length, area, rake factors - Print, email or message reports DECKING & FLOORING SETOUT, MATERIAL ESTIMATING and COSTING:- - Options for Insets, single or double bearers - Set Spacing type to maximum, fixed or equal - Set pricing for materials / labour to calculate cost and cost/area TIMBER SETOUT:- - Set Spacing type to maximum, fixed or equal - Insets at start and end. STUD WALLS SETOUT, MATERIAL ESTIMATING and COSTING:- - Raked or flat walls - Sizing, Quantity & Cost Estimates - Timber (studs, noggins, plates) & Sheeting - Comprehensive setout lists - bottom, top - Align sheets on width, length or no sheets STAIR FRAMING (currently for single stair runs):- Permits Multiple restrictions on risers, treads, inclines and also allows application of 2R+G (2R+TD in US) in jurisdictions required - to meet standards. Other than StairCalc (which is our Stair only app) we do not know of an app that does this simultaneously. Also calculations allow for situations where the overall stair rise and run are fixed or variable allowing maximum flexibility. - Number and size of step risers, treads, step inclines, - Step incline (Also changeable), - Stairwell opening, - Stringer Lengths CONCRETE CALCULATOR / ESTIMATOR:- - Calculate quantities for slabs, footings, round and rectangular/square holes. - Estimates total volume and cost allowing for waste. CONVERTER:- - Convert Lengths, Area, Volume: Metric and US/Imperial. - Work in Decimal units or Yds/Ft/In/Fraction format to Metric, decimal US. EASY TO USE GENERAL CALCULATOR WITH TAPE: - Calculate (add, subtract etc) directly in feet / inches / fractions or decimals. - Common functions for quick calculation EXTENSIVE HELP: Extensive help - Tap twice on most buttons for more info. Optimised for all iPhones and iPads in portrait mode. INFOGUIDE: Infoguide is part of a small building firm based in Western Australia. This app was created by a former Roof Framing Carpenter for our team of carpenters. We use it and believe it will be as helpful to other carpenters as it was for us. Terms of Service: http://www.apple.com/legal/itunes/appstore/dev/stdeula

Screenshots

Span Calc4 screens
Roof Guide4 screens

Verdict

The call

The clearest difference is rating: Roof Guide at 4.0 against Span Calc's 3.0. Roof Guide also leads on review sentiment (64% vs 30%). Span Calc's advantage is in-app purchases (none vs 4) and iOS requirement (14.2 vs 26.0). On price, ratings volume, update cadence and ads there is nothing between them.

Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS

CostPrice · In-app purchases · Ads · Monetization

Both are free to download. Roof Guide sells 4 in-app purchases, starting at $1.99 per month. Span Calc asks for nothing beyond the download.

ReceptionRating · Positive reviews · Number of ratings

Roof Guide holds the better App Store score, 4.0 against 3.0. Both are backed by a comparable volume of ratings — 16 and 19 respectively. Written reviews point the same way: 30% of Span Calc's written reviews are positive against 64% of Roof Guide's.

UpkeepUpdate frequency

Span Calc ships an update every 10 days, Roof Guide every 3 weeks. The most recent releases landed on November 1, 2026 and November 18, 2026 respectively.

Scorecard5 real differences · 5 level
Span Calc versus Roof Guide: the parameters behind the verdict, then further details
ParameterSpan CalcRoof Guide
PriceFreeFree
Rating3.0 (16 ratings)4.0 (19 ratings) — better
Positive reviews29.6% of reviews63.6% of reviews — better
Number of ratings1619 — better
Update frequencyEvery 10 days — betterEvery 3 weeks
AdsNoNo
In-app purchasesNo — betterYes
MonetizationFree — betterFree with in-app purchases
DevicesiPhone, iPad, iPod — betteriPhone, iPad
Requires iOS14.2 — better26.0
Further details — not scored
Size168 MB33 MB
Age rating17+4+
DeveloperAmerican Wood CouncilInfoguide Pty Ltd

Customer experience

Span Calc

All ratings15 ratings
Positive53.3%
Neutral0.0%
Negative46.7%
Written reviews27 reviews
Positive29.6%
Neutral11.1%
Negative59.3%

Roof Guide

All ratings19 ratings
Positive73.7%
Neutral0.0%
Negative26.3%
Written reviews11 reviews
Positive63.6%
Neutral0.0%
Negative36.4%

In-app purchases

None

Span Calc

No in-app purchases

4 purchases

Roof Guide

Subscriptions3
  • Monthly$1.991 Month
  • 6 Months$7.996 Months
  • Annual$12.991 Year
One-time1
  • Lifetime License$29.99

Questions

Is Span Calc free?
Span Calc is free to download, with no in-app purchases.
Is Roof Guide free?
Roof Guide is free to download, with in-app purchases available.
Which has better reviews, Span Calc or Roof Guide?
Roof Guide is rated higher. Span Calc averages 3.0 out of 5 from 16 ratings, while Roof Guide averages 4.0 from 19 ratings.
Do Span Calc or Roof Guide have ads?
Neither Span Calc nor Roof Guide shows ads.
Which is updated more often, Span Calc or Roof Guide?
Span Calc ships an update every 10 days, and Roof Guide every 3 weeks. Most recently, Span Calc was updated on November 1, 2026 and Roof Guide on November 18, 2026.

Other comparisons