BMS vs BMS Pal

This app allows users to bind their devices easily and conveniently at anytime and anywhere,view battery health status, and record, diagnose and warn the real-time status of the battery.It is a good helper for users in operating and maintaining their devices. 【Parameter settings】 Preset warning values for over-charge, over-discharge , over-current, and over-temperature,When the battery status reaches the preset warning value, the system will send out an alarm signal to remind users to pay attention to the battery's status and performance. 【Real-time data】 Summary data: including battery current, voltage, number of cells, cycle times, SOC, SOH, temperature and other parameters; Cell data: including independent voltage, independent current, cycle times, SOC, SOH, temperature and other parameters of the cell; Voltage temperature: including the number of cells, cell voltage, cell temperature and other parameters; Status data: including protection, indication, control, fault, battery balance, alarm and other status. 【Historical data】 Record the alarm state, protection state, fault occurrence state and development process of the battery history,which can help the users to understand the state and performance of the battery. 【Connection method】 Local control: Through Bluetooth communication, no need to log in with an account, directly search for nearby Bluetooth signals, one-to-one connection, ready to use; Remote control: through WIFI communication,need to register an account to log in, the APP and the device will automatically perform network distribution operations, and bind the account and device. 【My device】 Forgot password: reset password through email; Edit device: Long press the device item, the edit menu will pop up at the bottom, you can modify the device nickname or delete the device; Share device: Long press the device item, the device administrator who first configures the network and binds the account, can generate a QR code for the device for other users to scan the code to add.

All your batteries. One app. A JBD pack in the garage, a Victron in the van, a power station on the table - and a different vendor app for each one. BMS Pal ends the app-hopping: every pack you own in one live list, with state of charge, voltage, current, watts, and time remaining. Device detail pages have tools for a deep dive into your devices. Up to eight connected at once. EIGHT FAMILIES AT LAUNCH BMS boards get the deep treatment - per-cell voltages with live balancing indicators, protection alerts, chemistry detection, configuration reads, and confirmation-gated FET control: - JBD (including XiaoXiang and legacy variants) - JK - Daly Battery monitors and power stations get their essentials, with the same charts and history: - Victron (including encrypted advertising) - Junctek KL-F shunt monitors - Bluetti, Jackery, and EcoFlow power stations Coverage varies by family - the full who-reports-what table is at bmspal.app. WHAT IT DOES - Live telemetry: voltage, current, power, temperature, and state of charge stream in as your BMS reports them. Charts hold the last week, so you can see what happened while you slept. - Per-cell detail: every cell gets its own bar, down to the millivolt. Cells the BMS is balancing light up, so you can watch the spread tighten in real time. - Alerts, plainly stated: protection events appear in plain language. No sirens, no red flashing. Just the facts. - Groups: packs that work as one bank read as one battery. Group them series, parallel, or series-parallel and get combined voltage, current, and state of charge. - Capacity tests: run a real discharge test on any pack that reports current. BMS Pal integrates it over time against your cutoff and files the result in the pack's history, so "how many amp-hours, really?" gets a measured answer. - Chemistry detection: BMS Pal reads your protection thresholds and works out whether the pack is LiFePO4 or Li-ion. You can override it - you know your pack best. - Sanity Checks: not sure those numbers are fine? Send a snapshot of your pack for an AI review across six dimensions and get a written verdict back - findings graded by severity, with the reasoning and trade-offs spelled out. You see exactly what is sent before anything leaves your phone, and nothing is sent until you tap. BMS boards only, where the setup can actually be changed. - Write mode, off by default: toggling charge or discharge FETs is serious business on a high-energy pack. Writes sit behind a master switch plus a per-command confirmation, and every attempt is logged. LOCAL-FIRST. ACTUALLY LOCAL. No account, ever. No analytics, no trackers, no background traffic. Your telemetry history lives on your device; delete the app and it is gone. The only network calls are the ones you explicitly ask for (a Sanity Check or a problem report), and you see the exact payload first. THE DEAL Free download, and everything works for 7 days - every protocol, every feature, no card up front. Then $5 unlocks it for good: one purchase, no subscription, no "premium tier" holding features hostage. Sanity Checks run in the cloud and cost real server money, so the app includes 25 and $2 adds 25 more. Everything else runs entirely on your device. ONE DEVELOPER, ONE BENCH Every supported family sits on my bench: 92 wire-protocol variants documented, 1,100+ automated tests in the suite. Got a pack that will not identify, a value that reads wrong, or a feature idea? Report a Problem, Confirm Device Support, and Send Feedback are built in, replies land in your Support inbox, and none of it is ever paywalled. Your reports steer the roadmap. Runs on iPhone, iPad, and Apple Silicon Macs. JBD, XiaoXiang, JK, Daly, Victron, Junctek, Bluetti, Jackery, and EcoFlow are trademarks of their respective owners. BMS Pal is an independent project, not affiliated with or endorsed by any battery vendor. BMS Pal shows you what your BMS reports; it is not a substitute for proper fusing, wiring, and common sense.