DCS Lithium vs Outback Comms Fusion

DCS Lithium battery monitoring system. Time Remaining; Time remaining or time-to-go averaging period controls how smooth or stable the "Time remaining" estimate is. It does this by averaging load data over a set period of time (in minutes). The default value is 3 minutes. If you set it to 0 minutes, the system will show real-time duration without any averaging. However, this can make the "Time remaining" estimate jump around a lot. If you set it to 3 minutes, the system will smooth out short-term changes and only consider long-term trends, making the "Time remaining" estimate more stable. Cycle Count; The cycle count shows how much the battery has been used over its lifetime. For example, a 48V battery that powers a family home all day, every day, might rack up 200 cycles per year. On the other hand, a 12V battery in a caravan or fishing boat that’s only used occasionally might only reach 10 cycles per year. All DCS batteries come with an unlimited cycle warranty, meaning it doesn’t matter how often or how hard you use them - they’re built to last longer than any other batteries on the market. The "Current threshold" is fixed at 0.2A which helps ignore tiny electrical currents that could cause inaccurate battery readings. If the actual current is 0.0A but small electrical noise makes the battery monitor detect -0.05A, over time, this could incorrectly show that the battery is empty or needs recharging. With the Current Threshold fixed to 0.2A, the monitoring system treats anything smaller as zero, preventing these small errors and keeping the battery readings accurate. For a 12V battery to be considered fully charged, its voltage must be at least 14.0V. Once the battery monitor detects that the voltage has exceeded this level and the charging current has dropped below a set limit for a certain period, it will update the battery’s state of charge to 100%. Battery Status; A battery pack can be in one of three main states: Charging – The battery is gaining power Discharging – The battery is being used to power something Standby – The battery is in low-power mode, not charging or discharging While charging, the Battery Management System (BMS) checks the battery’s temperature and capacity to indicate whether it's being charged at a normal, fast, or super-fast rate. If something unusual happens - like the battery being completely drained, overcharged, charged too quickly, or getting too hot or too cold - the system will detect and display this information.

Fusion App is the official companion for your OutBack Comms Fusion router, the connectivity device built to keep you online in remote, rural, and off-grid Australia. It connects straight to your Fusion router over your local network, so you can set it up, keep an eye on performance, run tests, and put together reports you can share. It works alongside your Starlink dish too, so you get the full picture of your connection in one place. KEY FEATURES Your Fusion router at a glance See status, connected clients, and network details for your OutBack Comms Fusion device in real time. Starlink dish insight Check your connected Starlink dish status, signal quality, throughput, and uptime right next to your Fusion router. Alignment and obstruction tools Line up your dish for the clearest view of the sky and spot obstructions that get in the way of your signal. Speed test Measure download, upload, latency, and jitter against trusted servers, and keep track of your results over time. Stress test Run longer load tests with Fusion on or off to compare stability and catch dropouts before they catch you. Reports and export Create clean PDF and CSV reports of your speed, stress, and performance data, then email them or save them to your device. Smart alerts Battery warnings and shutdown timers help protect mobile and off-grid power setups. BUILT FOR THE OUTBACK Made for travellers, caravanners, remote workers, farms, and anyone who counts on staying connected far from the grid. Fusion App talks to your equipment locally, and you don't need an account to manage your own gear. WHY FUSION APP - Purpose-built for your OutBack Comms Fusion router - Real-time diagnostics, right on your device - Starlink and router status in a single view - Speed and stress testing with reports you can share Download Fusion App and take control of your connection. Support and contact: https://outbackcomms.com.au/pages/contact OutBack Fusion is a product of OutBack Comms. Starlink and Dishy are trademarks of Space Exploration Technologies Corp. (SpaceX). This app works with Starlink hardware but is not affiliated with, endorsed by, or sponsored by SpaceX.