Electro Sim vs TinyOhms

Build a circuit. See current flow. Understand how it works. Electro Sim turns electronics into something you can explore on your iPhone or iPad. Place components, connect wires, and run a simulation to see how your circuit responds. Whether you are learning the basics, preparing a classroom demonstration, or testing an idea, start with a working example or build your own. BUILD ON A CANVAS OR A BREADBOARD Create schematic circuits with drag-and-drop components and flexible wiring, or try a virtual breadboard with components and jumper wires. Zoom in to make connections, rotate parts, and use undo and redo as you experiment. SEE WHAT CHANGES WHEN YOU CHANGE THE CIRCUIT Follow animated current flow, inspect voltage and current readings, and use a virtual multimeter to explore circuit behavior. Adjust component values, toggle switches, or advance the simulation one step at a time to connect cause and effect. LEARN THROUGH WORKING EXAMPLES Explore LED circuits, capacitor charging, logic gates, adders, counters, seven-segment displays, and traffic lights. Selected examples include guided steps that help you investigate the circuit and check your understanding. FIND THE PARTS YOU NEED Browse a searchable component library with resistors, capacitors, inductors, diodes, LEDs, transistors, switches, buzzers, logic gates, and signal sources. Component descriptions and pin information help you decide what to use and how to connect it. TURN CIRCUIT BLOCKS INTO REUSABLE MODULES With Pro, create custom components from circuit blocks, define their pins, and reuse them in new projects. Build up a collection of modules as your ideas grow. Custom component creation and use require an active Pro subscription. SAVE AND SHARE YOUR WORK Save projects to revisit later, exchange circuit files in JSON format, and export circuit snapshots or PDF reports with readings and notes for learning and discussion. Designed for iPhone and iPad, with light and dark appearances and English, Simplified Chinese, and Traditional Chinese interfaces. Start with one LED, then see where your curiosity takes you.

TinyOhms opens straight onto a breadboard. Drop in a battery, a resistor and an LED, and the circuit runs the moment the loop closes. Current flows along the wires as moving chevrons, the LED glows brighter or dimmer with the real numbers, and if you push too much current through it, it pops. Nothing to install, nothing to solder, nothing to break. REAL PARTS, REAL MATH Every component behaves like the one in the drawer: resistors follow Ohm's law, LEDs have a forward voltage, transistors amplify, capacitors charge and drain, and the 555 timer ticks at the frequency its resistors and capacitor set. Under the hood is a full circuit solver (the same kind of nodal analysis SPICE uses), so the readouts are the ones you would measure with a meter. SEE WHAT IS HAPPENING • Live current flow on every wire, with direction and strength • Inspect mode: tap the eye to read every node voltage and branch current • A built-in scope that traces voltages over time — watch a capacitor charge, or a 555 output square wave • Real sound: buzzers beep and piezo speakers play the pitch the circuit sets • Room-light and temperature sliders to drive light sensors and thermistors • Short-circuit and overload warnings before anything "burns" BUILT FOR LEARNING TinyOhms is made for teens and any complete beginner. There is no lesson to sit through: build, watch, change one thing, and see what happens. Twenty ready circuits take you from a single LED to a light-following night light, a blinking timer, a one-shot pulse, a pitch control you can hear, and a traffic-light sequencer built from a 555 and a 4017 counter. YOUR OWN LIBRARY Sign in with just your email (a code, no password) to save circuits to your library and open them on the TinyOhms website Workbench too. Export any board as a SPICE netlist or share the board file. ON THE BENCH Free: wire, jumper, batteries (3 V, 4.5 V, 9 V), resistor, LED, switch, push button, buzzer, light sensor (LDR) and NPN transistor — everything the beginner projects need. TinyOhms Pro (optional monthly subscription): potentiometer, capacitor, 1N4001 diode, DC motor, thermistor, piezo speaker, the 555 timer and the CD4017 counter. Circuits from the library always open in full, whether or not you subscribe. TinyOhms Pro renews monthly until cancelled in Settings › Apple Account › Subscriptions. Under 18? Ask a parent first. Terms: https://tinyohms.com/terms/ Privacy: https://tinyohms.com/privacy/