Engineering Calculator HVAC vs CaptiveAire Toolbox
Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.
Engineering Calculator HVAC
Read full descriptionHide full description
HVAC engineering calculations in seconds — right on site, without an internet connection. Converting kgf/cm² to bar, checking the velocity in a pipe, sizing an expansion tank or picking a valve Kvs used to mean searching the web, leafing through a handbook and doing arithmetic in your head. Now your phone is enough. UNIT CONVERSION WITHOUT MISTAKES Enter a value once and see it in every unit of the category at the same time. Pressure, flow rate, power, energy, temperature, length, area, volume, mass and velocity: ten categories, about eighty units, including kgf/cm², mmH₂O, Gcal/h, BTU/h and psi. Any value is copied with a single tap, straight into an email or a bill of quantities. PIPE VELOCITY ACROSS EVERY SIZE AT ONCE Enter the flow rate and see the velocity for every pipe size, with a colour hint: where it is too low, where it is fine, where the pipe will get noisy. Steel to GOST 3262 up to DN 350, PP-R PN20, PEX and PE-RT, copper to EN 1057 — with real inner diameters, not nominal ones. Picking a diameter takes a couple of seconds. THERMAL POWER AND FLOW, BOTH WAYS Know the flow rate and you get the power. Know the power and you get the flow rate. Water, ethylene glycol and propylene glycol from 10 to 60 percent, with density and specific heat taken at the average temperature rather than approximated. The result comes in kW, kcal/h and Gcal/h at once. VALVES Pressure drop across a control or balancing valve from its Kvs, and the reverse task: which Kvs is needed for a given drop. In bar, kPa and metres of water column. EXPANSION TANK Required membrane tank volume, the nearest standard size, the expansion volume and the tank efficiency. The system volume can be estimated from the installed power. If the temperatures or pressures are inconsistent, the app says so instead of returning a neat but wrong number. PIPE INSULATION Surface area, area per metre, insulation volume and the insulated diameter — numbers ready for a bill of quantities. REFERENCE DATA INSIDE Steel water and gas pipes to GOST 3262 from DN 15 to DN 350, PP-R PN20, PEX and PE-RT, copper pipes to EN 1057. Water density and specific heat by temperature, properties of water and glycol mixtures, volumetric expansion coefficients, the standard range of expansion tanks from 5 to 1000 litres and typical insulation thicknesses by diameter. WHY IT WORKS ON SITE • Fully offline: no internet needed in a basement or on a construction site • Nothing extra: no ads, no sign-up, no subscriptions, no permissions • Input accepts both a comma and a dot, the numeric keyboard opens by itself • Russian and English, light and dark theme • Selected units and settings are remembered WHO IT IS FOR HVAC and plumbing designers, heating and water supply installers, service engineers of boiler houses and heat substations, energy auditors and students of related fields. Written by a practising HVAC engineer for himself and his colleagues. Free.
CaptiveAire Toolbox
This app provides over 40 HVAC and building-systems engineering calculators. It's designed for field use, offering quick calculations for cooling, heating, ventilation, electrical, piping, and valve sizing based on industry standards.
- 40+ HVAC engineering calculators
- Cooling and heating load calculations
- Ventilation and airflow analysis
- Electrical sizing tools
- Piping and duct sizing
- Valve and flow sizing
- Reference data and psychrometric chart
Read full descriptionHide full description
The CaptiveAire Toolbox puts 40+ HVAC and building-systems engineering calculators in your pocket. Designed for engineers, contractors, and technicians, every formula uses standard industry references (ASHRAE, AMCA, NEC), sized so you can run sanity checks in the field instead of pulling out a laptop. Cooling: Total Cooling Load (enthalpy-based with humidity), Sensible Cooling Load, Latent Cooling Load, SEER, Cost of Cooling, Tons to BTU/hr conversions, DX/MPU Cooling, Evaporative Cooling, DMUA mode logic, Cooling Density Factor. Heating: BTU output for direct and indirect fired heaters, Input and Output BTU/hr for IBT systems, Temperature Rise from BTU and CFM, Heat Pump capacity with airflow and outdoor temperature adjustment, Reheat Coil leaving conditions, Manifold Pressure for natural gas and LP, Heating Density Factor. Ventilation and Airflow: Room Volume CFM, Sensible Heat CFM, Cooling Load CFM, Duct Velocity CFM, Outdoor Air Load (sensible plus latent), Psychrometric properties from dry bulb plus RH or wet bulb, Fan Energy Index per AMCA 208, Motor Adjusted Frequency for VFDs, ERV ROI Calculator with degree-day economics. Electrical Sizing: Wire Size per NEC Table, MCA and MOCP for motor circuits, Amperage from horsepower. Piping and Structural: Round Duct Sizing using Darcy-Weisbach and Colebrook-White, Duct Velocity and Friction, Piping Pressure Drop with fittings equivalent length, Pitched Roof curb height variation. Valve and Flow Sizing: Kv from flow rate, flow rate from Kv, pressure drop from Kv, Cv to Kv conversion, Heat Load to Flow Rate for water and glycol. Reference: ASHRAE Weather Station data with autocomplete address search, returning heating and cooling design temperatures, solar irradiance, wind speeds, and monthly design-day temperatures. Interactive Psychrometric Chart with property calculations. Modern HVAC versus Traditional Rooftop Unit comparison. Each calculator includes the formula and variable definitions accessible from the title bar. Tap the info icon to see exactly what equation drives the result. Built by the engineering team at CaptiveAire Systems. No tracking, no ads, no account required.
Screenshots
Verdict
The clearest difference is update cadence: CaptiveAire Toolbox at weekly against Engineering Calculator HVAC's every 6 months. On price, ads, in-app purchases and device support there is nothing between them.
Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS
Both are free to download. Neither carries in-app purchases, so what you see is what you pay.
Engineering Calculator HVAC ships an update every 6 months, CaptiveAire Toolbox weekly. The most recent releases landed on November 9, 2026 and November 13, 2026 respectively.
| Parameter | Engineering Calculator HVAC | CaptiveAire Toolbox |
|---|---|---|
| Price | Free | Free |
| Rating | — | 5.0 (1 ratings) — better |
| Number of ratings | — | 1 — better |
| Update frequency | Every 6 months | Weekly — better |
| Ads | No | No |
| In-app purchases | No | No |
| Monetization | — | Free |
| Devices | iPhone, iPad, iPod — better | iPhone, iPad |
| Requires iOS | 15.0 — better | 16.0 |
| Further details — not scored | ||
| Size | 19 MB | 71 MB |
| Age rating | 4+ | 4+ |
| Developer | aleksandr bronnikov | CaptiveAire Systems, Inc. |
In-app purchases
Engineering Calculator HVAC
No in-app purchases
CaptiveAire Toolbox
No in-app purchases
Questions
Is Engineering Calculator HVAC free?
Is CaptiveAire Toolbox free?
Do Engineering Calculator HVAC or CaptiveAire Toolbox have ads?
Which is updated more often, Engineering Calculator HVAC or CaptiveAire Toolbox?
Other comparisons















