Live BMS vs BMS Pal

Live BMS puts every one of your lithium batteries on a single, beautiful dashboard — no more switching between manufacturer apps. Connect over Bluetooth to your LiFePO4 packs and watch what actually matters, live: state of charge, pack voltage, current, per-cell voltages, temperature, cycle count, and health. A liquid-fill charge ring and clear in/out power flow make each battery readable at a glance, and a running estimate tells you how long until the pack is full while charging or empty while it's under load. Built for people running more than one battery — on a boat, an RV, a van, or an off-grid solar setup. WATCH FROM ANYWHERE (OPTIONAL) Add the Live BMS Link, a small Wi-Fi bridge that sits with your batteries, and your dashboard keeps updating when you're nowhere near the boat. Without it, Live BMS works exactly as it always has — Bluetooth only, nothing leaves your phone. FEATURES • One dashboard for all your batteries, updating in real time • Auto-detects supported BMS units — no fiddling with settings • Live "time to full" and "time to empty" at the current rate • Battery banks: group the packs wired together and see one combined charge, power draw, and runtime • Trip tracking: compare where you started to now, burn rate, and days remaining at your current use • Per-cell voltage bars and imbalance so you can spot a weak cell • History charts for charge, voltage, and current • Remote output on/off, including a master switch for all batteries • Alerts for low charge, high temperature, and cell imbalance — with plain-language guidance on what to set • Optional Live BMS Link accessory for checking your batteries from anywhere • Fahrenheit or Celsius, and Light / Dark / System themes FREE VS PRO The free version shows live charge and voltage for one battery — so you can prove it works with your hardware before paying anything. A single $4.99 unlock adds everything else: full telemetry, trips, history, alerts, power control, banks, and unlimited batteries. SUPPORTED BATTERIES Works with LiTime, Power Queen, and Redodo LiFePO4 batteries, plus common JBD / Xiaoxiang, JK-BMS, and Daly BMS units. More families are being added. PRIVACY Live BMS has no accounts, no ads, and no analytics. It talks directly to your batteries over Bluetooth and stores your history on your phone. If you add the optional Live BMS Link, your own battery readings pass through our server so you can see them remotely — nothing else does, and none of it is tied to your name, your email, or anything that identifies you. Note: Live BMS is an independent app and is not affiliated with or endorsed by LiTime, Power Queen, Redodo, or any BMS manufacturer.

All your batteries. One app. A JBD pack in the garage, a Victron in the van, a power station on the table - and a different vendor app for each one. BMS Pal ends the app-hopping: every pack you own in one live list, with state of charge, voltage, current, watts, and time remaining. Device detail pages have tools for a deep dive into your devices. Up to eight connected at once. EIGHT FAMILIES AT LAUNCH BMS boards get the deep treatment - per-cell voltages with live balancing indicators, protection alerts, chemistry detection, configuration reads, and confirmation-gated FET control: - JBD (including XiaoXiang and legacy variants) - JK - Daly Battery monitors and power stations get their essentials, with the same charts and history: - Victron (including encrypted advertising) - Junctek KL-F shunt monitors - Bluetti, Jackery, and EcoFlow power stations Coverage varies by family - the full who-reports-what table is at bmspal.app. WHAT IT DOES - Live telemetry: voltage, current, power, temperature, and state of charge stream in as your BMS reports them. Charts hold the last week, so you can see what happened while you slept. - Per-cell detail: every cell gets its own bar, down to the millivolt. Cells the BMS is balancing light up, so you can watch the spread tighten in real time. - Alerts, plainly stated: protection events appear in plain language. No sirens, no red flashing. Just the facts. - Groups: packs that work as one bank read as one battery. Group them series, parallel, or series-parallel and get combined voltage, current, and state of charge. - Capacity tests: run a real discharge test on any pack that reports current. BMS Pal integrates it over time against your cutoff and files the result in the pack's history, so "how many amp-hours, really?" gets a measured answer. - Chemistry detection: BMS Pal reads your protection thresholds and works out whether the pack is LiFePO4 or Li-ion. You can override it - you know your pack best. - Sanity Checks: not sure those numbers are fine? Send a snapshot of your pack for an AI review across six dimensions and get a written verdict back - findings graded by severity, with the reasoning and trade-offs spelled out. You see exactly what is sent before anything leaves your phone, and nothing is sent until you tap. BMS boards only, where the setup can actually be changed. - Write mode, off by default: toggling charge or discharge FETs is serious business on a high-energy pack. Writes sit behind a master switch plus a per-command confirmation, and every attempt is logged. LOCAL-FIRST. ACTUALLY LOCAL. No account, ever. No analytics, no trackers, no background traffic. Your telemetry history lives on your device; delete the app and it is gone. The only network calls are the ones you explicitly ask for (a Sanity Check or a problem report), and you see the exact payload first. THE DEAL Free download, and everything works for 7 days - every protocol, every feature, no card up front. Then $5 unlocks it for good: one purchase, no subscription, no "premium tier" holding features hostage. Sanity Checks run in the cloud and cost real server money, so the app includes 25 and $2 adds 25 more. Everything else runs entirely on your device. ONE DEVELOPER, ONE BENCH Every supported family sits on my bench: 92 wire-protocol variants documented, 1,100+ automated tests in the suite. Got a pack that will not identify, a value that reads wrong, or a feature idea? Report a Problem, Confirm Device Support, and Send Feedback are built in, replies land in your Support inbox, and none of it is ever paywalled. Your reports steer the roadmap. Runs on iPhone, iPad, and Apple Silicon Macs. JBD, XiaoXiang, JK, Daly, Victron, Junctek, Bluetti, Jackery, and EcoFlow are trademarks of their respective owners. BMS Pal is an independent project, not affiliated with or endorsed by any battery vendor. BMS Pal shows you what your BMS reports; it is not a substitute for proper fusing, wiring, and common sense.