My LoopCal vs SignalScale
Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.
My LoopCal
Streamline 4-20mA loop checks with guided calibration worksheets and instant signal conversion. Generate PDF reports, manage instrument history, and perform loop power calculations offline. Designed for field technicians.
- Guided calibration worksheets (3-21 points)
- As-found/as-left runs with error reporting
- Signal conversion (4-20mA, 0-10V, etc.)
- PDF and CSV report generation
- Instrument history and calibration reminders
- Loop power calculations
- Offline functionality
Read full descriptionHide full description
LoopCal turns a 4–20 mA loop check into a calibration worksheet you can hand over, and it is the quickest way to convert a signal in the field. Built for instrumentation and calibration technicians. Fully offline. FROM CHECK TO WORKSHEET • Guided three-point, five-point, and custom 2–21-point checks • As-found and as-left runs, with the error and pass/fail at every point • Up-scale and down-scale readings with hysteresis • Tolerance as percent of span, signal units, or engineering units • Worst point and maximum error summarized for you • A clean PDF worksheet with your company name and logo, in US Letter or A4, plus CSV for your records CONVERT IN SECONDS • 4–20 mA, 0–20 mA, 0–10 V, 1–5 V, and your own custom signal endpoints • Direct-acting and reverse-acting ranges • Linear and square-root (flow) transfer functions • Engineering ranges with any unit, including negative and offset spans • Percent, signal, and engineering values update as you type, with the substituted formula shown • Verify this loop: take the range you just entered straight into a check EVERY INSTRUMENT ON RECORD • Save instruments with their ranges and calibration history • See what is coming due, and get a reminder before the next calibration • Reopen a saved instrument and start its next check without retyping the range LOOP POWER MATH • Shunt resistor voltage drop • Required supply voltage and remaining compliance • Maximum loop and wire resistance PRIVATE BY DESIGN • Everything runs on your device. No account, no ads, no tracking, no network. LoopCal is a calculation aid and field worksheet — not a calibrator, an accredited calibration service, or a replacement for manufacturer procedures. Always follow site lockout/tagout, operations authorization, device manuals, and approved procedures. Terms of Use (EULA): https://www.apple.com/legal/internet-services/itunes/dev/stdeula/
SignalScale
Read full descriptionHide full description
SignalScale turns analog signals into measurement values and back. Set your signal and measurement ranges, enter a value, and see the result immediately. SIGNAL PRESETS 4–20 mA, 0–20 mA, 0–10 V, 2–10 V, 0–5 V, 1–5 V and −10–10 V are built in. Use Custom range for other endpoints and units. CONVERT IN BOTH DIRECTIONS Convert a measured signal into pressure, temperature, speed or another quantity. Switch direction to calculate the signal corresponding to a target measurement. Increasing and decreasing ranges are supported. Values outside the configured range are extrapolated and clearly marked. SAVE ANALOG CHANNELS Keep multiple analog input (AI) and analog output (AO) configurations with individual names, ranges and units. Load a saved channel, update it or save a new copy. VISUALIZE AND SHARE View the linear scaling curve and reference values at 0%, 25%, 50%, 75% and 100%. Export an English-language chart as a vector PDF or high-resolution PNG through the iOS share sheet. OFFLINE CALCULATIONS Calculations and saved channels work offline. No account, ads or analytics. Calculator settings and channels are stored locally on your device. Example: 4–20 mA mapped to 0–10 bar gives 5 bar at 12 mA. SignalScale performs linear calculations using values you enter. It does not connect to instruments, measure electrical signals, diagnose sensor faults or perform square-root extraction.
Screenshots
Verdict
The clearest difference is in-app purchases: SignalScale at none against My LoopCal's 3. On price, ads, device support and iOS requirement there is nothing between them.
Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS
Both are free to download. My LoopCal sells 3 in-app purchases, starting at $2.99 per month. SignalScale asks for nothing beyond the download.
| Parameter | My LoopCal | SignalScale |
|---|---|---|
| Price | Free | Free |
| Rating | 5.0 (1 ratings) — better | — |
| Number of ratings | 1 — better | — |
| Update frequency | Every 10 days | — |
| Ads | No | No |
| In-app purchases | Yes | No — better |
| Monetization | Free with in-app purchases | — |
| Devices | iPhone, iPad | iPhone, iPad |
| Requires iOS | 17.0 | 17.0 |
| Further details — not scored | ||
| Size | 3 MB | 1 MB |
| Age rating | 4+ | 4+ |
| Developer | Neobile LLC | Ernst Birox |
In-app purchases
My LoopCal
- Monthly$2.991 Month
- Annual$9.991 Year
- Lifetime$19.99
SignalScale
No in-app purchases








