OFFSET vs Bendwise
Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.
OFFSET
Read full descriptionHide full description
You are on a lift with a stick of three-quarter EMT and a bender, and the phone in your pocket does not know what a shrink is. OFFSET tells you where to put your marks — and then watches you make the bend. Give it the height you need and the angle you want. It gives you back the distance between marks, the shrink, and how far from the end of the pipe the first mark goes — in inches and sixteenths, the way it is written on the pipe, not as a decimal you have to convert on a ladder. LAY THE PHONE ON THE PIPE Every other bending app hands you a number and goes back in your pocket, which leaves the part where mistakes actually happen unwatched. OFFSET reads the angle off the phone's own tilt sensor. Rest it on the straight leg, tap Zero, and pull — a tone climbs as you close on the angle and holds steady when you are on it, because at that moment both hands are on the handle and a screen is no use to anyone. IT LEARNS YOUR SPRINGBACK Steel does not stay where you put it. Pull to thirty, let go, and the pipe relaxes a few degrees short. The phone never leaves the conduit, so it knows what you pulled to and what it settled at, and the difference is your springback. After a few bends it stops guessing and starts telling you to pull to thirty-three for a thirty — for your bender, at your size, in your hands. BENDS • Offset • Rolling offset, for a run that moves sideways and up at once • Kick • Three-point saddle, over a pipe or a beam • Four-point saddle, over something wide • 90-degree stub-up to a finished height • Back-to-back 90s FILL • Conduit fill to NEC Chapter 9, Tables 1, 4 and 5 • Box fill to NEC 314.16(B) YOUR BENDER, NOT A GENERIC ONE Take-up is a property of the tool in your hand. Pick Klein, Ideal, Greenlee, Milwaukee, Gardner Bender or Southwire in EMT or rigid, or enter your own. If the number stamped on your bender disagrees with the book, correct it — the correction is kept for that bender and that size, and every calculation after it uses your figure. TWO DRAWINGS, NOT ONE The top drawing is the finished bend. The bottom one is the stick as it is right now — straight, on the floor, with the marks where the pencil actually goes and dashed lines joining each bend to the mark that makes it. Take hold of the grip on the drawing and the height follows your thumb, a sixteenth at a time, with the marks moving as it changes. BUILT FOR A JOBSITE • Big type and big targets, so it works in gloves • Dark screen, so it does not blind you in a dark ceiling • Step a number a sixteenth at a time, or tap it and type it on a keypad that works in fractions instead of decimals • Every answer shows its working, so you can check it before you pull the handle • No account, no ads, no subscription, and no signal needed to calculate • Free to use for offsets, 90-degree stub-ups and the angle gauge THE MATH The multipliers are the field-standard ones you were taught — 6, 2.6, 2, 1.4 and 1.2 — not raw trigonometry, so the marks agree with the numbers printed on your bender and with what the journeyman next to you worked out in his head. Saddles use their own multipliers, because a 22.5-degree bend in a saddle is not the same as a 22.5-degree bend in an offset. ANY ANGLE, NOT JUST FIVE Your bender is stamped for 10, 22.5, 30, 45 and 60, and those five carry the taught multipliers. But an obstacle sits where it sits, so you can type any angle from 1 to 90 and the app falls back to the trigonometry those taught values approximate — and tells you, on screen, which of the two it used. Inches and NEC. This is the US edition. OFFSET is a calculation aid, not a substitute for your own training or for the code. Take-up, radius and springback differ between benders, so check every figure against the tool in your hands and measure the bend before you cut. Terms of Use: https://sirekapps.com/terms Privacy Policy: https://sirekapps.com/privacy
Bendwise
Read full descriptionHide full description
Bend marks in three taps. Bendwise is a conduit bending calculator app built for electricians and apprentices. Enter your offset depth, pick an angle, and get the first mark, the distance between marks, and the shrink, with take-up already figured in. It covers offsets, saddles, kicks and 90 degree bends in EMT, IMC and rigid, from everyday EMT bending on a hand bender to 4" rigid on a hydraulic bender. EVERYDAY BENDS, FREE - Offset bends, with shrink and the offset multiplier shown - 90° stub-ups and back-to-back 90s - Kicks and kick 90s - 3-point and 4-point saddle bends - Angle check: lay your phone on the bent leg and see PASS, OVER or UNDER MATCHED TO YOUR CONDUIT BENDER - 350 benders built in and free to use: hand, mechanical, electric and hydraulic, for EMT, IMC and rigid, 1/2" to 4" - Radius and deduct come from the makers' own manuals and catalogs wherever they are published - Marks follow the centerline radius of your shoe, and one switch takes you back to the conduit bending chart you already know - A warning when a bend cannot be made, before you waste a stick of pipe BUILT FOR THE JOB SITE - Big, high-contrast numbers you can read at arm's length - A light theme for direct sun - Fractions to 1/16", feet and inches, millimeters or centimeters - Type the numbers or slide them with a gloved thumb - Works fully offline. No ads, no account, no data collected BENDWISE PRO (ONE-TIME PURCHASE) - Rolling offsets, parallel offsets and matching offsets - Matching and parallel kicks - Compound 90s around a column or a box, and segmented 90s - Calibrate your own bender: bend one test stub, enter the measurement, and every result after that matches your shoe - Save bends by job, lay several bends out on one conduit, and export a PDF cut sheet Pay once. No subscription. FOR JOURNEYMEN AND APPRENTICES Whether you call it conduit bending or pipe bending, Bendwise is an electrician's calculator that does one job. Journeymen get the marks fast when the run has to go in today. Apprentices see the math on every result (radius or multiplier, shrink, mark spacing), so the numbers start to make sense. Bendwise gives guidance; always confirm against your bender's own marks. Bendwise is an independent app and is not affiliated with any bender manufacturer.
Screenshots
Verdict
The clearest difference is device support: Bendwise at 3 against OFFSET's 1. Bendwise also leads on iOS requirement (15.0 vs 17.0). On price, ads and in-app purchases there is nothing between them.
Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS
Both are free to download. OFFSET sells 1 one-off in-app purchase and Bendwise sells 1 one-off in-app purchase. Whichever you choose, the download price is not the number that matters.
| Parameter | OFFSET | Bendwise |
|---|---|---|
| Price | Free | Free |
| Ads | No | No |
| In-app purchases | Yes | Yes |
| Devices | iPhone | iPhone, iPad, iPod — better |
| Requires iOS | 17.0 | 15.0 — better |
| Further details — not scored | ||
| Size | 8 MB | 21 MB |
| Age rating | 4+ | 4+ |
| Developer | Piotr Sirek | Andrew Putranto |
In-app purchases
OFFSET
- OFFSET Pro$4.99
Bendwise
- Bendwise Pro$7.99









