Comparison

BendMark vs Conduit Fill

Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.

Head to head
About

BendMark

Features
Read full description

Stand at the bender, enter two numbers, get the mark. BendMark gives you the distance from the end of the pipe to every bend mark, in sixteenths of an inch, so you can find it on your tape without converting anything. Works with no signal. Nothing is fetched. FIFTEEN BENDS • Offset, rolling offset and parallel offset, evenly spaced or measured pipe by pipe for a rack of mixed sizes • Matching offset and kick: the angle that lines up with a pipe already bent, by the gap between its marks or by its rise • 3-point and 4-point saddles • 90° stub-up, back-to-back 90° and kick with 90° • Kick, parallel kick and matching kick • Compound 90° around a round, square or rectangular obstruction • Offset to fit: finish at a known length, and it says what to cut • Segment bend, for a large radius in many shots • Concentric 90°, for a bank of pipes round one corner YOUR BENDER, YOUR NUMBERS Pick Klein, Ideal, Greenlee, a rigid and IMC head, or the Greenlee 555 electric. Not listed? Type in your own take-up, gain and radius for each size. Marks follow the head you are actually holding, which is where most cut-short mistakes start. ANY ANGLE 10, 22½, 30, 45 and 60 on the chips, or type any angle from 5° to 89°. Slide a finger across any field, or across the rule on the keypad, to trim it a sixteenth at a time with a click for each step. Choose the centreline radius method for exact marks, or the classic multiplier table; where the two disagree, the app shows you both rather than pretending. READ AN ANGLE OFF THE PIPE Lay the phone on a leg you have already bent and it reads the angle off gravity. Zero it on the flat leg first, so the floor counts as nothing. MARKS WHERE YOUR BENDER WANTS THEM A hand bender lines its arrow up with the mark. Powered benders and saddle notches want the centre of the bend instead. Switch once, and every screen follows. LEARN THE TRADE Six short pages for a break in the van: take-up and gain, shrink, centreline radius, the three marks on the shoe and what each is for, the order you bend in, and working safely. ONE STICK, EVERY BEND Lay several bends on one length, get every mark from the same end, the total shrink and the pipe you need. Read them back from the far end when the bender only reaches that side. Copy the lot into your notes, save the stick, bring it back tomorrow. STEP BY STEP AT THE BENDER Every bend comes with numbered instructions: where to measure, where the arrow goes, which way to roll the pipe, how to check it. The diagram points at the mark each step is talking about, so you never lose your place. TABLES IN YOUR POCKET Offset multipliers and shrink per inch. Take-up and gain for every size. Bender specs: travel and radius adjustment at every angle, and where to scribe your own shoe so it reads angles without a protractor. Sixteenths to decimals to millimetres. Outside diameters for EMT and rigid conduit. BUILT FOR THE SITE • Sixteenths, never decimals. A tape measure has no 12.625 on it. • Feet and inches, or millimetres if that is how your prints are drawn. • Big targets you can hit with gloves on. • Plain-words warnings when a bend cannot be made, and what to change. NO ACCOUNT, NO SERVER, NO ADS No sign-in, no subscription, no network. Pay once. That is the whole transaction.

About

Conduit Fill

Features
Read full description

Will it fit. What it loses. What you pull. Offline field calculator for US residential and light-commercial electricians. One job carries the same wires across Fill, V-Drop, and Wire. Switch 2023 and 2026 in the header. One $7.99 purchase. No subscription, no account, no ads. WILL IT FIT Kitchen default is 14.8% FITS on ½" EMT with 3Ɨ#12 THHN plus a bare #12 ground. Status words stay shop talk: FITS, TIGHT, OVER. Ground uses bare area and does not upsize with the hots. WHAT IT LOSES Tap 20A rec. The 85 ft run goes HIGH at 4.5%. Upsize hots to #10 (2.8%). Ground stays #12. Feet are one-way, not the loop. WHAT YOU PULL The answer is the AWG. Put #10 on the pull because voltage drop at 85 ft, not because ampacity ran out. WHAT PIPE For EMT use ½". Types stay in shop order — EMT, then PVC, IMC, RMC — not ranked by fill percent. HAND THIS TO THE INSPECTOR One-page PDF with the job, pipe, wires, fill, voltage drop, and what you pull. Free PDFs carry a SAMPLE mark. FREE AND UNLOCK Free: fill on EMT and THHN, one What pipe?, one V-Drop, one saved job, 2026, SAMPLE PDF. $7.99 once: unlimited V-Drop and What pipe?, Wire, 2023 and 2026, 50 jobs, clean PDF. Restore lives in Settings. Works in airplane mode. Tables ship in the app. This is a field calculator. It is not NFPA 70, not the codebook, and not AHJ approval. Verify every pull against the edition your inspector is using. ā—† Privacy Data Not Collected. No tracking. ā—† Terms of Use https://www.apple.com/legal/internet-services/itunes/dev/stdeula/ ā—† Support https://conduitcalc.txyou.com/support

Screenshots

BendMark4 screens
Conduit Fill4 screens

Verdict

The call

The clearest difference is price: Conduit Fill at Free against BendMark's $4.99. BendMark's advantage is in-app purchases (none vs 1) and device support (3 vs 1). On ads there is nothing between them.

Scored on Price Ā· Rating Ā· Positive reviews Ā· Number of ratings Ā· Update frequency Ā· Ads Ā· In-app purchases Ā· Monetization Ā· Best chart rank Ā· Devices Ā· Requires iOS

CostPrice Ā· In-app purchases Ā· Ads Ā· Monetization

Conduit Fill is free to download; BendMark costs $4.99 up front. Conduit Fill sells 1 one-off in-app purchase. BendMark asks for nothing beyond the download.

Scorecard4 real differences Ā· 1 level
BendMark versus Conduit Fill: the parameters behind the verdict, then further details
ParameterBendMarkConduit Fill
Price$4.99Free — better
AdsNoNo
In-app purchasesNo — betterYes
DevicesiPhone, iPad, iPod — betteriPhone
Requires iOS13.0 — better17.0
Further details — not scored
Size17 MB7 MB
Age rating4+4+
DeveloperOguzhan CART就擪 邓

In-app purchases

None

BendMark

No in-app purchases

1 purchases

Conduit Fill

One-time1
  • Unlock the job$7.99

Questions

Is BendMark free?
BendMark costs $4.99, with no in-app purchases.
Is Conduit Fill free?
Conduit Fill is free to download, with in-app purchases available.
Do BendMark or Conduit Fill have ads?
Neither BendMark nor Conduit Fill shows ads.

Other comparisons