Live Audio Multi vs CueRemote

Live Audio Multi-Tool (LAM-T) is a fast, offline toolbox for live sound engineers, system techs, AV installers, and musicians. Everything you reach for at a gig — an analyzer, an SPL meter, a delay calculator, sub-array alignment, a signal generator — in one clean app. No account, no ads, no tracking. REAL-TIME ANALYZER (RTA) • Fractional-octave RTA with a live peak readout • A / C / Z weighting • Spectrogram view, freeze, peak hold, and capture/compare • Adjustable Y-offset for quick reference matching SPL METER + Leq • dB(A), dB(C), dB(Z) with peak hold • Running Leq over 1, 15, or 60 minutes • Per-device calibration offset — match it to a real meter once and it sticks DELAY CALCULATOR • Speed-of-sound delay from real temperature and humidity (auto-filled from your location) • Connect a Bluetooth laser rangefinder to drop a measured distance straight in — verified with the Bosch GLM 165-27C (GLM 120 C family); Leica DISTO (and Stabila LD), older Bosch GLM, Stanley TLM99s / DeWalt DW099S and older Mileseey on a best-effort basis; any other meter can send a one-tap diagnostic report so support can be added • Feet or metres SUB-ARRAY DESIGNER • Broadside and end-fire arrays • Cardioid tops (castellated or all-subs) • Per-sub delay times computed for your spacing and coverage SIGNAL GENERATOR • Sine (20 Hz–20 kHz, log sweep), pink noise, and a polarity-check pulse • Polarity reader — check a speaker's polarity through the mic UNIT CONVERTERS • Temperature, distance, and pressure • Reads your device's barometer for true local air pressure Built for the real world: it works offline, launches instantly, and stays out of your way. Informational only, no warranty. Measurements and conversions are estimates — verify anything critical with calibrated instruments.

CueRemote is a remote control for operating QLab 5 from an iPhone or iPad over your venue’s local network. See the live workspace, cue lists, playhead, and running or paused cues. Control GO, STOP, pause, resume, and playhead navigation with an interface designed for rehearsals and live shows. LIVE CUE CONTROL • GO, STOP, pause, resume, and stop each running cue individually. • Load to Time: load a cue at a chosen point before GO, using the slider or buttons. • Go to Cue: enter a cue number to fire it or move the playhead to it. • Yellow progress bars show running, paused, and loaded cue progress, including pre-wait. • Selecting another cue resets the previous cue and updates Load to Time. • Open or close a Group in CueRemote and it updates in QLab. • Select cues and move the playhead from the list. • Switch cue lists from your device; GO fires the list shown in CueRemote. • Carts: tap a cue to fire it. • Lock controls to prevent accidental changes during a show. • Get a warning when QLab and CueRemote show different cue lists. CONNECTION • Discover QLab automatically with Bonjour or connect manually by IP address. • OSC over TCP with automatic reconnection. • Connection status stays visible. Stale workspace data is identified and unsafe commands are disabled. PRIVACY CueRemote requires no account, has no ads, and uses no analytics or tracking. Connection data stays on your device. The QLab passcode is stored in the device’s Keychain and is not synced to iCloud. REQUIREMENTS • A Mac running QLab 5. • iOS or iPadOS 17.6 or later. • Your iPhone or iPad and Mac must be able to communicate over the local network. • Enable OSC access in QLab and grant View and Control permissions. CueRemote never requests Edit permission. QLab runs the show and plays its media. CueRemote displays workspace state and sends OSC control commands; it does not create, edit, or delete cues. QLab is a trademark of Figure 53, LLC. CueRemote is not affiliated with or endorsed by Figure 53.