Audio Frequency Analyzer vs Enigma Semi

"Audio Frequency Analyzer" is a powerful real-time audio analyzer (RTA) app for iPhone. With its simple operation, you can easily measure and evaluate your sound environment. This app measures the frequency response in 30 split band scale of 1/3 octave in real time. It can also display the FFT analysis results. It supports calibration for 1/3-octave bands. By adjusting the characteristics to match not only the built-in microphone but also your external microphone, it achieves high measurement accuracy. "Audio Frequency Analyzer" can be used for various applications, including sound room tuning, speaker settings, audio equipment testing, stage setup measurement, sound mixing environment evaluation and noise environment investigation. Features: - Frequency spectrum response measurement of 1/3 octave unit, 30 bands. (OCT) - FFT Analyzer (FFT) - Observation frequency range: 20 - 23000 Hz - Logarithmic amplitude display. - Touch-scroll function to adjust visible amplitude ranges. - Display the measured value of 1/3 oct bands at OCT mode. (dB@OCT) - Function to change the graph slope at FFT mode. (Slope): -3dB/oct (less than 1kHz), +3dB/oct (1kHz or higher) - Peak hold function. (Hold) - Average display function. (Avg): Time linear averaging. Fast-2.56sec, Slow-12.8 sec - Display response control. (Fast/Slow) - Reset of Measurement display position. (Scroll) - Snapshot of Measurement display. (Snap) - Calibration function in OCT mode. (Calibrate): 1/3 octave band offset and total offset setting. - Supports built-in microphone, headset microphone, and external digital audio connection. Note: The first time you access your microphone and photos after installing the app, the iOS system will ask you for permission to access them. If you have not enabled this setting, the app will not be able to access them due to iOS system privacy restrictions. Please enable the access permission in the iOS setting "Settings > Privacy & Security > Photos or Microphone". Please visit our iOS app support page for more information about this app.

Enigma Semi-Full PRO mode exclusive operation application. This application is for Enigma Semi-Full only. It can not be used for the conventional another Enigma series. This application is only for PRO mode which can set the ignition time. Professional knowledge is required to set the ignition timing. EASY mode has special application which can make adjustment from ignition timing of normal ECU without advanced expert knowledge. This application can be downloaded for free. When it is free, you can connect with all Enigma Semi-Full, but only the tachometer screen is displayed. (Only tachometer and TPS are displayed). In order to set various functions of Enigma Semi-Full, you need to purchase the bike model corresponding to Enigma Semi-Full you have from the model selection screen. When purchasing and selecting bike model , the following functions can be used. - Preset a data combined. Preset data can be easily written to Enigma Semi-Full. - The ignition timing of 0 - 60 degrees can be adjusted for each engine rotation / throttle position. It is also possible to set the dwell time. - The fuel injection amount can be set for each engine rotation / throttle position. - Fuel correction at idling can be performed. - Startability and idling stabilization correction function when using a big injector. (Only for compatible models) - Adjustment of fuel injection time by engine temperature and intake air temperature is possible. - It is possible to set injection timing at each rotation speed. - Various maps can be displayed in 3D graph. - Two maps can be put inside Enigma Semi-Full, and it can be switched with an external switch. - In real time, you can display tachometer, throttle opening monitor, injector opening / closing rate, oil / water · engine temperature (depending on model),Voltage (Applicable models only),Air-fuel ratio(Applicable models only). - Display the current engine speed and throttle position in real time in the fuel & ignition adjust map. - Revolution Limit can be set . - Pit-in limit can be set (Applicable model only) - Digital acceleration pump can be set. - It is possible to correct the TPS sensor according to the actual machine. - You can make several fuel data and save it, you can change it immediately when you need it. - It corresponds to Japanese and English. No pairing is necessary. On the Bluetooth setting screen, Enigma is not searched. Please turn on Bluetooth on the Bluetooth setting screen, then exit the setting screen with the Home button, launch the application, and connect from "Connect to Semi-Full" of the application.