RadBeacon vs Egress Recon

The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services. The RadBeacon app from Radius Networks requires an iOS iPhone, iPad or iPod touch running iOS 7.1 or higher and equipped with Bluetooth 4.0 capabilities. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. Once discovered, you can display each beacon's operating settings and make modifications to those settings. Scanning for RadBeacons ------------------------------ Scan for nearby configurable RadBeacons by swiping down on the RadBeacons table. Each beacon discovered is displayed with the following summary details - Beacon Name - Beacon Model - Firmware Version - Hardware ID - Battery Level Reviewing RadBeacon Settings ------------------------------------ Select any RadBeacon in the table to view it's detailed settings. The settings displayed include: _Summary_ - Beacon Name - Beacon Model - Firmware Version - Hardware ID - Battery Level _Modifiable Settings_ - Beacon Name - Beacon Type - Advertised Organizational Identifier [ UUID ] - Advertised Group Identifier [ Major ] - Advertised Unit Identifier [ Minor ] - Advertised Measured Power - Advertisement Rate - Transmit Power Updating RadBeacon Settings ----------------------------------- Change any of the modifiable settings. Press the Action Menu button and select Apply. Submit a valid PIN to update the settings for this beacon. Calibrating Measured Power --------------------------------- Press the Action Menu button and select Calibrate. Calibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Update the measured power value with the results of your calibration activity and update your settings. Range Your Beacon ----------------------- Press the Action Menu button and select Range. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Update RadBeacon PIN ---------------------------- Press the Action Menu button and select Update PIN. Submit a new and existing PIN to update the PIN for your beacon. Reset to Factory Settings ----------------------------- Press the Action Menu button and select Reset. Reset the device to the original factory settings. Submit a valid PIN to reset the settings for your beacon to factory defaults. Lock Settings ---------------- Press the Action Menu button and select Lock. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON. A beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. Boot To DFU --------------- Press the Action Menu button and select DFU. Reboot the beacon into Direct Firmware Update mode. Contact Radius Networks support for information on the procedure for firmware update or replacement. In order to re-enter normal operational model, simply remove and replace power to the device.

You are on a guest Wi-Fi you did not choose. Something will not connect and nobody can tell you why. Egress Recon answers that from your phone, in under a second. WHICH PORTS GET OUT Sixteen common outbound ports, tried against real public services. You get more than "open" or "closed": • Refused and timed out are different answers. One means something on the network actively rejected the connection; the other means it was dropped silently. • Intercepted is its own finding. The connection succeeded, but the thing that replied was not the service you asked for — a portal, a proxy, or a middlebox re-signing TLS. WHAT NAT YOU ARE BEHIND Your public address, and whether your NAT gives you a reusable mapping or a symmetric one — the reason a video call falls back to a relay. Carrier-grade NAT is reported with its confidence and the evidence behind it, never as a bare label. IPv6 and NAT64 state, and whether you can reach your own public address from inside. WHAT IT DOES TO DNS Whether plain DNS gets out. Whether the network's resolver agrees with a public one. Whether it invents answers for names that cannot exist. And whether DNS over HTTPS and DNS over TLS still work when plain DNS does not — each tested with a real query, not just a connection. WI-FI VERSUS CELLULAR The most useful thing a network tool can tell you is "this Wi-Fi blocks it, and your cellular connection does not." Egress Recon runs the same tests over both and shows the difference — attributing it correctly in both directions, because blaming the café for something your carrier blocks helps nobody. BEHIND A CAPTIVE PORTAL It tells you the portal is there, shows the URL it is pushing you to, and labels the results "before you sign in." Sign in, run again, and it shows you exactly what changed. IT SHOWS ITS WORK Every verdict comes with what was actually observed: the banner the server sent, the certificate it presented and who issued it, the exact response that came back. You can check the reasoning instead of trusting a colored label. Where something cannot be determined, it says so and why. Two ports in the standard set have no public server to test against, so they stay untested rather than showing a red cell that means nothing. Share any run as text, a web page, a PDF, or JSON. Saved runs are grouped by network. PRIVACY • No analytics, no telemetry, no accounts, no ads, no third-party SDKs. • It never scans your network. Every probe goes to a public internet service — never your router, never your other devices. That is why it never asks for local network permission. • It does not read your Wi-Fi name. That needs location permission, which it never requests. • Saved runs stay on your device. A report leaves only when you share it. Egress Recon for Mac and for iPhone and iPad are both free apps on one App Store record. Requires iOS 17 or iPadOS 17.