Electronics Engineer Helper vs Engineering FMEA

Digital toolbox for electronics engineers and electricians. Calculators and references for beginners and professionals — for work, study, DIY, and repair. Used by over 100,000 users. Completely ad-free. Included tools: • Datasheet search • Equivalent parts search (cross reference for transistors, diodes and ICs) • Resistor color and digit marking (4, 5 and 6 band color code; 2 symbols, 3/4 digit and EIA-96 code SMD resistors code) • Electronic schematic symbols (IEC 60617, IEEE 315 and GOST standards) • Pinouts of connectors and interfaces (USB, HDMI, DisplayPort, DVI, VGA, Thunderbolt, Apple Lightning and 30-pin, SATA, PCI Express and M.2, Ethernet RJ45 with PoE, RJ11/RJ14/RJ25, RS-232/422/485, IEEE 1394 FireWire, ATX, computer fans, SD card, audio jack, RCA, MIDI, XLR, PS/2, D-sub, SMEMA) • Pinouts of boards and microcontrollers (Raspberry Pi and Pico, Arduino, ESP32, ESP8266, STM32 Nucleo, Teensy, Orange Pi, RADXA Rock Pi, LubanCat, Flipper Zero, ATmega and ATtiny) • Ohm's law calculator • AWG converter (wire diameter, cross-section area, resistance and maximum current) • Resistor for LED • Voltage divider • Wheatstone bridge (output voltage or unknown resistance, current and power of every arm) • Capacitor code • Capacitor markings • Capacitor ESR tables • Frequency response curve calculation of passive filters (RC, RL, RLC, LC) • Inductor color code • Air-core coil calculator (inductance or number of turns of a single-layer solenoid) • Ideal transformer (winding turns, voltages and currents) • Linear current regulator • SMD packages list • Reactance • PCB trace resistance • Active, apparent and reactive power • RMS converter (peak, RMS and peak-to-peak values for seven waveform shapes) • 555 waveform generator • Operational amplifiers • RLC circuit • Number conversion • Unit converter • Cable voltage drop • Battery life (runtime of a battery pack, with discharge curve) • NTC thermistor resistance • Logic gates • RC circuit • Decibels calculator • 25-pair cable color code • Fuse color marking Additionally, by purchasing the PRO version of the app, you will get access to additional tools: • SMD components marking codes • Diodes color code (Pro Electron, JEDEC and JIS-C-7012 standards) • Linear voltage regulator • Resistor value to color or SMD code marking converter • Voltage rectifier • Series or parallel electrical components' connection calculator • Diode voltage drop • Minimum PCB trace width • Analog to digital conversion • Attenuators • 4-20 mA signal converter • Thermocouple calculator • Resistance thermometer • Buck switching voltage regulator • Wire resistance • Zener diode regulator (Zener diode and series resistor selection from a catalogue of 438 parts) • Load cell (bridge output voltage to weight, force, pressure or torque) • BJT voltage divider biasing • Transformer turns per volt (from core area, flux density and frequency) • Junction temperature (with or without a heatsink, power derating curve) • Solar string dimensioning (minimum voltage and current ratings for a PV array) • Solar cable and fuse selection (NEC and IEC rules) • 555 astable generator with variable duty cycle • NTC thermistor in a voltage divider and with an ADC input Privacy Policy: https://www.eehelper.app/ios/privacy/ Terms of Use: https://www.eehelper.app/ios/terms/

Engineering FMEA for iPad Engineering FMEA for iPad is designed for fast, structured engineering documentation with a strong educational focus. The primary purpose of the app is to support learning and applying systematic thinking in engineering problem analysis through the FMEA methodology. The app can also be used for practical needs such as FMEA reporting, rapid preparation of preliminary data for urgent meetings, team selection, and tracking corrective actions. A sample Wind Turbine FMEA project, including references and tutorial content, is automatically added on first installation (clean install required). Reporting Capabilities • The content of the full report can be customized using settings options. • A complete report preview is generated when the Report button is pressed. • Each section includes its own dedicated report button for partial reporting. • Users can upload and save project-specific logo images by tapping the logo area on the notification page. Supported Sections 1. Notification Report with an editable photo 2. Team Management Table 3. FMEA Table for Design or Process FMEA • Severity, Occurrence, and Detection scale descriptions automatically adapt to the selected FMEA type • Design and Process FMEA entries can be combined within a single table 4. Document Review Table 5. Recommended Actions Report Data Editing & Reuse Any previously entered record in a table can be recalled into the entry fields by selecting its row. After editing, updates can be saved or recorded as a new entry using the command buttons. Reporting & Sharing The full report is previewed before publishing. Sharing options allow the report to be opened with third-party apps such as PDF editors and viewers. Help & Guidance Context-specific help content is available in the Settings tab of each project.