Electronics Engineer Helper vs KUKA MixedReality Assistant

Digital toolbox for electronics engineers and electricians. Calculators and references for beginners and professionals — for work, study, DIY, and repair. Used by over 100,000 users. Completely ad-free. Included tools: • Datasheet search • Equivalent parts search (cross reference for transistors, diodes and ICs) • Resistor color and digit marking (4, 5 and 6 band color code; 2 symbols, 3/4 digit and EIA-96 code SMD resistors code) • Electronic schematic symbols (IEC 60617, IEEE 315 and GOST standards) • Pinouts of connectors and interfaces (USB, HDMI, DisplayPort, DVI, VGA, Thunderbolt, Apple Lightning and 30-pin, SATA, PCI Express and M.2, Ethernet RJ45 with PoE, RJ11/RJ14/RJ25, RS-232/422/485, IEEE 1394 FireWire, ATX, computer fans, SD card, audio jack, RCA, MIDI, XLR, PS/2, D-sub, SMEMA) • Pinouts of boards and microcontrollers (Raspberry Pi and Pico, Arduino, ESP32, ESP8266, STM32 Nucleo, Teensy, Orange Pi, RADXA Rock Pi, LubanCat, Flipper Zero, ATmega and ATtiny) • Ohm's law calculator • AWG converter (wire diameter, cross-section area, resistance and maximum current) • Resistor for LED • Voltage divider • Wheatstone bridge (output voltage or unknown resistance, current and power of every arm) • Capacitor code • Capacitor markings • Capacitor ESR tables • Frequency response curve calculation of passive filters (RC, RL, RLC, LC) • Inductor color code • Air-core coil calculator (inductance or number of turns of a single-layer solenoid) • Ideal transformer (winding turns, voltages and currents) • Linear current regulator • SMD packages list • Reactance • PCB trace resistance • Active, apparent and reactive power • RMS converter (peak, RMS and peak-to-peak values for seven waveform shapes) • 555 waveform generator • Operational amplifiers • RLC circuit • Number conversion • Unit converter • Cable voltage drop • Battery life (runtime of a battery pack, with discharge curve) • NTC thermistor resistance • Logic gates • RC circuit • Decibels calculator • 25-pair cable color code • Fuse color marking Additionally, by purchasing the PRO version of the app, you will get access to additional tools: • SMD components marking codes • Diodes color code (Pro Electron, JEDEC and JIS-C-7012 standards) • Linear voltage regulator • Resistor value to color or SMD code marking converter • Voltage rectifier • Series or parallel electrical components' connection calculator • Diode voltage drop • Minimum PCB trace width • Analog to digital conversion • Attenuators • 4-20 mA signal converter • Thermocouple calculator • Resistance thermometer • Buck switching voltage regulator • Wire resistance • Zener diode regulator (Zener diode and series resistor selection from a catalogue of 438 parts) • Load cell (bridge output voltage to weight, force, pressure or torque) • BJT voltage divider biasing • Transformer turns per volt (from core area, flux density and frequency) • Junction temperature (with or without a heatsink, power derating curve) • Solar string dimensioning (minimum voltage and current ratings for a PV array) • Solar cable and fuse selection (NEC and IEC rules) • 555 astable generator with variable duty cycle • NTC thermistor in a voltage divider and with an ADC input Privacy Policy: https://www.eehelper.app/ios/privacy/ Terms of Use: https://www.eehelper.app/ios/terms/

Fast robot commissioning with the help of Augmented Reality (AR): It connects the real with the virtual world, thus enriching the environment of the robot cell with digital information in a clear and uncomplicated manner. This not only accelerates installation, but also makes working with the robot safer, as errors can be detected and corrected quickly. With the software, a created safety configuration can be examined and verified at a glance. All relevant data is graphically displayed in real-time directly on the robot: Monitoring spaces, safety-oriented tools and the cell area. The display of the corresponding configuration parameters of the spaces or tools is also possible. In addition, movements can be simulated with a virtual robot and tool. This allows potential collisions to be detected without having to move the physical robot. Furthermore, with the integrated demo mode the functions can be tried out without an actual robot. The app is easy to set up and operate: After installation on the iPhone or iPad, all relevant robot data is sent directly from the controller to the mobile device via WLAN through a router or access point (not a KUKA product) and displayed visually. The KUKA.MixedReality Safe technology package is used for this purpose, which needs to be installed on the robot controller. In addition, the KUKA.SafeOperation technology package must be installed to use the safety functions.