Ruler vs 鉄筋定尺カット計算

Scale Ruler is the simple application to display the scale of various measurement units. ※ Warning: - The accuracy of the scales cannot be guaranteed. - Calibration and PPI values ​​will be reset when the model changes. - Set the PPI value only when the model is undecided. - When you change the PPI value, perform calibration after the change. ■How to use: ■Select mode In UNLOCKED state, after choosing measurement unit, magnification ratio and reduced scale, the scale is displayed. ■Free mode When dragging the screen at UNLOCK, you can set the scale in the range 1: 1 to 1: 100. When you press and hold the scale value, the keyboard is displayed and you can enter the scale. You can lock the scale on the ruler with a switch. Sorry for the advertisement during unlocking. After In-App Purchase, your ads will no longer be displayed. Specification of Scale Ruler - measure length meter,inches - magnification ratio 50% , 70.7% , 100% , 141% , 200% - reduced scale 　for meter　 　　1:100 , 1:150 , 1:200 , 1:250 , 1:300 , 1:400 , 1:500 , 1:600 　for inch 　　1:1 , 1:1.5 , 1:2 , 1:2.5 , 1:3 , 1:4 , 1:5 , 1:6 　for inch(Architectural) 　　1:1 , 1:2 , 1:4 , 1:8 , 1:12 , 1:16 , 1:24 , 1:32 , 1:48 , 1:64 　　1:96 , 1:128 , 1:192 , 1:384 　for inch(Engineering) 1:120 , 1:240 , 1:360 , 1:480 , 1:600 , 1:720 1:800 , 1:960 , 1:1080 ■ Settings - Calibration - PPI (pixels per inch) setting - In-app purchase (ads not displayed) - In-app purchase restoration ■ Calibration Adjust the length of the ruler. Use the correct ruler for adjustment. "Calibration" button: Records the adjusted state and reflects the calibration result on the ruler. "Reset" button: Returns the adjustment status to the specified value. It will not be recorded. "Initialize" button: Returns the adjustment status to the specified value and reflects it on the ruler. * Caution: The calibration value will be reset when the model changes. ■ PPI (pixels per inch) setting If the model is undecided, check the PPI value of the model before setting the PPI value. * Please set only when the model is undecided. "OK" button: Record the entered PPI value and reflect it on the ruler display. "Initialize" button: Returns the PPI value to the specified value and reflects it on the ruler. * Caution: The PPI value will be reset when the model changes.

■鉄筋の定尺カットをすばやく計算 「鉄筋定尺カット計算」は、定尺鉄筋から必要長の鉄筋を何本切り出せるかを計算できる、現場向けのシンプルな計算アプリです。 定尺と必要長を入力するだけで、取得できる本数と余り長さを瞬時に表示します。 余計な機能を省いたシンプルなUIで、現場でも素早く確認できます。 ■主な機能 ・鉄筋定尺カット計算 ・取得できる本数を表示 ・余り長さを表示 ・計算履歴の保存 ・計算結果のコピー ■計算方法 本アプリでは以下の計算を行います。 取得本数 floor(定尺 ÷ 必要長) 余り 定尺 % 必要長 ■こんな方におすすめ ・鉄筋工 ・施工管理 ・現場監督 ・配筋計画を行う方 ・数量確認を素早く行いたい方 ■注意 本アプリの計算結果は目安としてご利用ください。 最終的な配筋・施工・数量確認は図面・仕様書・施工条件などをご確認ください。