iCon Control

September 9, 2024

- Improved the field boundary creation workflow - The ability to auto-complete drawing of a field boundary - You can now create multiple boundaries within a single job - Added the ability to cancel field boundary recordings - Improvements to bin chaining - Bin "empty" transition weight is now a configurable option - Added run until empty option. This allows you to continue dispensing product at the minimum rate, until the bin is empty, after switching to the next bin in the chain. - Updated setting default values - Highlight time for blockage is now 30 seconds - Opener lookaheads are now 8 seconds for engage and 0 for disengage - Tank lookaheads are now 8 seconds for engage and 0 for disengage - Added the ability to broadcast product while openers are lifted - Enhanced job reports to show if products were removed while a job was in progress. - Improvements to Blockage alarms - Fixed a bug that caused the blockage alarm popup to be displayed with a delay after the audible alarm - Fixed a bug that could cause the audible blockage alarm to be falsely triggered when sections were disabled - Added the ability to manage product profiles outside of a job - Improvements to prescription maps - Fixed a bug that prevented the default rate to be adjusted when using a prescription map - Fixed a bug that caused the multiplier for NH3 to be displayed incorrectly - Fixed a bug that resulted in prescription map legend to be cut-off - Fixed a bug that caused application rates to display incorrectly when using a prescription map - Added additional diagnostic information for connected GPS units

February 15, 2024

Release notes: • New UI with Väderstad theme • Various mapping improvements • Updated Job Format which allows export for FMIS through Seed Hawk Cloud • Support for 14-Port CAN Blockage ECU • Possible to Downgrade Firmware from 3.1 to 2.7 Important Downgrading/Upgrading Note: Users must end or delete all existing jobs before performing an upgrade from 2.7 → 3.1 or performing a downgrade from 3.1 → 2.7

March 15, 2023

Release Details: Gateway 260 firmware 2.7.10.700 Gateway 100 firmware 2.0.8.564 Bug Fixes: -Fixed a bug that cause the bin pressure reading to be a negative value. -Fixed a bug that reduced the obstacle creation limit. -Fixed a bug that cause the Quick Dump Timer to count 1 less than the set value. -Fixed a bug that cause the bin pressure reading to be a negative value. -Fixed a bug that affects the blockage count upon disabling an airstream. Known Issues: -Switching to manual control and back to SCT while SCT override is in progress does not turn SCT on. Workaround: Cancel SCT override after switching to manual control. -PM4/LC3 replacement workflow reaches an invalid state after being used more than once. Workaround: Close and Reopen the iPad app or select DONE and restart the workflow.

May 25, 2022

Bug Fixes

April 28, 2022

Bug Fixes

April 7, 2022

The software includes following features: • New Configuration Workflow in the Tech App. • Tempo Support. • SCTx Feature Unlocks. • Work Lights.

May 6, 2021

Gateway 260 firmware 2.0.8.568 Gateway 100 firmware 2.0.8.564 Improvements -general improvements to system stability -resolved compatibility between generation 8 iPads and Bluetooth switchbox

October 27, 2020

Gateway 260 firmware 2.0.6.480 Gateway 100 firmware 2.0.6.478 Bug Fixes -Addressed a connectivity issue pertaining to iOS14

March 26, 2020

Gateway 260 firmware 2.0.6.480 Gateway 100 firmware 2.0.6.478 New Features -Update the address claim procedure for LC3 devices so that their addressing is compatible with the KarTech bin remote system. Bug Fixes -Fixed a critical bug that would cause the iCon app to exhibit detrimental performance when drawing as-applied data on the map. -Fixed a bug that would cause combined tanks to empty to 100 lbs instead of 200 lbs while using Fit To Field. -Fixed a visual defect with the strike-through graphic for a disconnect blockage section. -Fixed a bug that would cause a System Voltage Alarm to be incorrectly triggered if the Wing PM4 was disconnected. -Updated the mapping initialization to fix a bug that could cause parts of the client UI to fall out of sync with the system state. -Fixed a bug that prevented the GW260 from powering off cleanly during a fatal voltage condition. -Fixed a bug that would cause the default NH3 application rate to be incorrect when using a prescription map. -Fixed a bug that could cause a slave client to get into a bad state if it is not on the operate screen when a new job is started. -Fixed a bug that could cause the blockage settings to fall out of sync on a slave device. -Fixed a bug in the way map tiles were being sent that could prevent them from loading on a client device. -Fixed a bug that could cause extremely large job files to appear corrupt. -Fixed a bug that could occasionally cause the generation of the configuration backup archives to be significantly delayed. -Updated the PM4 firmware to fix a bug that prevented the PID control algorithm from maintaining a 0% duty cycle at lower frequencies. -Fixed a bug that would cause the Gateway's WiFi get in a bad state if multiple pairing commands are sent within a 2 minute period. -Fixed a problem with the workflow for pairing individual WBMs by serial number. (Does not affect Pair-All) -Fixed a bug that could cause the iCon application to crash when using a prescription map with a file name over 33 characters long. -Fixed a bug that would occasionally prevent an RX map from loading if it had space characters in its file name. -Fixed a bug where the gateway would attempt to start a job before the prescription maps had finished transferring from the iPad. When this occurred, the job would be started without the prescription map, but no error would be shown to the user. Improvements -Improved the double-tap detection algorithm to help prevent obstacles from being toggled accidentally. -Improved the logic for rendering map to ensure that there are no flickering areas on the map. -Added logic to adjust the max zoom as a field boundary is being defined such that the entire boundary can be viewed at once. Known Issues -PM4/LC3 replacement workflow will reach an invalid state after being used more than once on one iPad. To use the replacement work flow more than once, either close/reopen the iPad app or select "done" and restart the workflow. -Occasionally when an iPad times out due to master/slave logic, the application will not automatically reconnect and will remain on a nonfunctional operate screen. If the application is not responding to commands (Turning sections on/off, SCT override, etc), manually close out of the iPad application and reopen it. -The WBM snapshot feature does not correctly save the color of the section numbers in the status bar when the fans are toggled -The Lookahead Calibration workflow will provide invalid results if the disengage button is held longer than the engage button. While this does not affect functionality, it prevents the workflow from continuing until the lookaheads are manually adjusted, which may be non-intuitive for the user. Instruct the user to manually adjust the lookahead values to be within the valid ranges.

March 18, 2020

Gateway 260 firmware 2.0.5.449 Gateway 100 firmware 2.0.5.444 New Features -Update the address claim procedure for LC3 devices so that their addressing is compatible with the KarTech bin remote system. Bug Fixes -Fixed a critical bug that would cause the iCon app to exhibit detrimental performance when drawing as-applied data on the map. -Fixed a bug that would cause combined tanks to empty to 100 lbs instead of 200 lbs while using Fit To Field. -Fixed a visual defect with the strike-through graphic for a disconnect blockage section. -Fixed a bug that would cause a System Voltage Alarm to be incorrectly triggered if the Wing PM4 was disconnected. -Updated the mapping initialization to fix a bug that could cause parts of the client UI to fall out of sync with the system state. -Fixed a bug that prevented the GW260 from powering off cleanly during a fatal voltage condition. -Fixed a bug that would cause the default NH3 application rate to be incorrect when using a prescription map. -Fixed a bug that could cause a slave client to get into a bad state if it is not on the operate screen when a new job is started. -Fixed a bug that could cause the blockage settings to fall out of sync on a slave device. -Fixed a bug in the way map tiles were being sent that could prevent them from loading on a client device. -Fixed a bug that could cause extremely large job files to appear corrupt. -Fixed a bug that could occasionally cause the generation of the configuration backup archives to be significantly delayed. -Updated the PM4 firmware to fix a bug that prevented the PID control algorithm from maintaining a 0% duty cycle at lower frequencies. -Fixed a bug that would cause the Gateway's WiFi get in a bad state if multiple pairing commands are sent within a 2 minute period. -Fixed a problem with the workflow for pairing individual WBMs by serial number. (Does not affect Pair-All) -Fixed a bug that could cause the iCon application to crash when using a prescription map with a file name over 33 characters long. -Fixed a bug that would occasionally prevent an RX map from loading if it had space characters in its file name. -Fixed a bug where the gateway would attempt to start a job before the prescription maps had finished transferring from the iPad. When this occurred, the job would be started without the prescription map, but no error would be shown to the user. Improvements -Improved the double-tap detection algorithm to help prevent obstacles from being toggled accidentally. -Improved the logic for rendering map to ensure that there are no flickering areas on the map. -Added logic to adjust the max zoom as a field boundary is being defined such that the entire boundary can be viewed at once. Known Issues -PM4/LC3 replacement workflow will reach an invalid state after being used more than once on one iPad. To use the replacement work flow more than once, either close/reopen the iPad app or select "done" and restart the workflow. -Occasionally when an iPad times out due to master/slave logic, the application will not automatically reconnect and will remain on a nonfunctional operate screen. If the application is not responding to commands (Turning sections on/off, SCT override, etc), manually close out of the iPad application and reopen it. -The WBM snapshot feature does not correctly save the color of the section numbers in the status bar when the fans are toggled -The Lookahead Calibration workflow will provide invalid results if the disengage button is held longer than the engage button. While this does not affect functionality, it prevents the workflow from continuing until the lookaheads are manually adjusted, which may be non-intuitive for the user. Instruct the user to manually adjust the lookahead values to be within the valid ranges.