REAMP vs VintageRack

This effect is a complex spectral saturation processor simulating a set of different analog gear in a new and unique way. Benefits of this algorithm is that it is highly CPU efficient and adds (almost) no latency. The 7 models available are based on real analog gear individually measured in two dimensions; gain responses (-inf dB to +6 dB) at the frequency spectrum 20Hz to 20kHz. This data is used to transform input audio to output audio. Models: Cassette Deck A consumer cassette deck produced in the mid 80’s. This profile adds some nice grit in the lower mids and rolls off the higher spectrum in a very pleasant way. 1/4” Tape Reel A high quality tape reel machine was used for this profile. Set to one channel mode, there was plenty of dynamic bandwidth to capture on this one. Adds some subtle tape saturation that oozes mid 70’s. Preamp Tube Clean / Preamp Tube Drive These two profiles are captured from a high end tube microphone preamp with two different input gain levels (normal gain on the Clean version and a boosted level on the Drive version). Used on only one channel, this profile is very subtle, but the impact adds up when several channels are used simultaneously. Guitar Tube Clean / Guitar Tube Drive The guitar amp used is a well known pro amp used by several pro guitar players, and Just like the Preamp Tube profiles, these are recorded with two different input gain levels. Tube Bass Amp One of the developers friends dad had an old bass amplifier that we borrowed and profiled. Tip: Run a Fender Jazz bass through it and your neo soul licks will sound just like they’re supposed to. Usage: Since there are several models available, this one can be used on almost any type of audio in any genre. The output can span from lo-fi to high-end hifi. One approach is to put it on several tracks with a more subtle setting which makes the essence of the gear simulated add upp. Another is to put it on the mix, or a bus. Since we’re in the digital domain there can be some added aliasing when distorting the signal too much, resulting in an unpleasant high frequency boost. To prevent this, set the HARMONICS switch to SOME or FEW. Feature list • Seven handpicked profiles based on gear we love available. • Spectral drive (four bands) • Dry / Wet mix • Plenty of factory presets • Ultra low latency • Optional 8x oversampling Full documentation available inside the app or at https://klevgrand.se/downloads/reamp-docs/ REAMP works both as a standalone app and as an AUv3 plugin.

VintageRack is a minimalistic and convenient multi-effect application that contains modules realistically modeling notable retro gear from the early digital era with their inherent aesthetics and atmosphere. Most of the effects in this application have been inspired and based on the principles of actual hardware from the 70s and 80s, which is great for giving the sound of any instrument the nostalgic and emotional mood of old recordings. This application has a clean and intuitive user interface with a well-considered structure. The signal path is split into seven slots: the first for input control, the last for output, and five customizable effect modules in between. Each module features a master fader for adjusting effect presence and a mute button for smooth toggling. These parameters can be easily assigned to MIDI controls right from the main screen, improving both workflow and productivity. Smooth transitions between presets and on-screen pads for quickly switching presets that can be easily assigned to MIDI controls allow flexible effect selection during live performances or studio recordings. Another great feature of VintageRack is the ability to set a lower bit depth of processed signal, typical for early digital devices, both for the entire path and for individual modules. As with these devices, this application models pre- and post-processing of the analog signal both before and after the digital circuits with the addition of companders, emphasis and filters, which makes the sound similar to the real devices. Effect modules: - Analog modeled compressor. - Three band equalizer typical for mixing consoles. - Classic and reverse delays with modulation feature. - Two Chorus modules are precise emulations of known devices. - Two modules of Flanger with different options and tones. - Two modules of Phaser with various sound character. - Filter module controlled by LFO or envelope generator. - Faithful emulation of classic Wah effects with added automation. - Combined effect of Tremolo and Vibrato with separate rate. - Ring modulator with additional modulation of carrier. - Three types of Fuzz with modulated filters. - Emulation of one of the early digital reverbs. - Vintage exciter with bass enhancer. - Spring reverb with tube preamp. - Advanced formant filter with voice synth mode. - Input slot contains Noise gate and Automatic gain control. - Output slot contains tape-style saturation and three types of tonestacks. VintageRack is a universal application for iOS and macOS. It can work on iPhone and iPad as well as Mac / MacBook with M1 chip (and later). VintageRack works on iPhone and iPad standalone, as an Audio Unit or Inter-App Audio module, and supports Audiobus and Ableton Link. On MacOS, VintageRack can works both as a standalone application and as an Audio unit (AUv3) with DAWs and other hosts that support AUv3 plugins. All application features are available on iOS and macOS, including MIDI support (with a MIDI learn option) and audio unit parameters. VintageRack has a built-in detailed description of all parameters also available as PDF file on the application site. Demo: https://youtu.be/I3lcd5rYaBQ https://youtu.be/zmHjpFDkPLQ https://youtu.be/eqkvhDBUGPQ https://youtu.be/o79g6S5qftk You can find more information on VintageRack and other creative audio apps at: https://motion-soundscape.blogspot.com