Comparison

Resistor Code Calculators vs EL tools

Price, ratings, monetisation and update history for both apps, side by side โ€” with what reviewers say about each.

Head to head
About

Resistor Code Calculators

Features
Read full description

The one handy app for electrical engineering calculation. This app contains not only resistor color code and capacitor code calculators but also electrical filter, attenuator, rectifier, LC oscillator, RF, PCB trace, cable, Ohm's Law, skin effect, Lumen Candela conversion, Delta Y Conversion, and many other handy calculators.

About

EL tools

Features
Read full description

All the everyday calculations for electrical design, in one app. When you're designing a circuit, small questions keep coming up: "Will this resistor pair give me the voltage I need?" "What's the rise time of this RC circuit?" "What do three resistors in parallel add up to?" "Where is the cutoff frequency of this filter?" "Which resistors give this amplifier a gain of 10?" "What resistor do I need for 10 mA through this LED?" "What value is this resistor with these color bands?" "What is 0x3F8 in binary?" Too small to open a spreadsheet, but you want the answer right now. EL tools is a practical calculator for electrical design that lets you check these things quickly on your phone. โ–  Voltage Divider Enter the input voltage and target output voltage, choose a standard resistor series (E6/E12/E24/E48), and instantly find the R1/R2 combinations closest to your target. The min/typ/max output voltage is shown for each combination, taking resistor tolerance (and input voltage tolerance) into account. Useful for power supplies, voltage references, and ADC inputs. โ–  RC Step Response Calculate the time constant ฯ„ = RC from the resistance and capacitance. View the rise (charge) or fall (discharge) curve as a graph, and check the voltage at any elapsed time with a slider. Handy for reset, delay, and smoothing circuits. โ–  Combined Resistance and Capacitance Supports series and parallel connections. Calculate the nominal, minimum, and maximum combined value from up to three resistors or capacitors and their tolerances. โ–  Filters Supports low-pass (RC/RLC), high-pass (RC/RLC), band-pass (RLC), and pi (CLC) filters. See the cutoff frequency, damping ratio, or the band-pass center frequency, Q, and bandwidth, with the frequency response shown as a Bode plot. Check a pi filter from its values, or design a 3rd-order Butterworth pi filter from a target cutoff and resistance. โ–  Op-Amp Gain Choose an inverting or non-inverting amplifier, enter the target gain, and find the closest Rf/Rg combinations from a standard resistor series (E6/E12/E24/E48). The min/typ/max gain is shown for each combination, taking resistor tolerance into account. โ–  LED Current-Limiting Resistor Get a standard resistor value from the supply voltage, LED color or Vf, target current, and number of LEDs in series. See the min/typ/max current with tolerances, the resistor power, and a suggested rating. If the supply is too low, the app tells you how many LEDs it can drive and the voltage you need. โ–  Parts Read resistor color codes (4 or 5 bands), or look up the colors for a value. Decode chip resistor markings (3-digit, 4-digit, R notation, EIA-96), and check a chip size table with metric and inch codes, dimensions, and typical power ratings. โ–  Programmer Calculator Convert values between HEX, DEC, OCT, and BIN at a glance. Tap individual bits to toggle them, and choose the word size (8/16/32/64-bit) and signed (two's complement) or unsigned. Run bitwise operations (AND, OR, XOR, NAND, NOR, NOT, shifts, rotates) and arithmetic, then feed the result back in to keep going. โ–  Useful for - Checking values while designing circuits - Choosing resistor and capacitor values - Designing voltage dividers for power circuits - Checking RC delay times and filter cutoff frequencies - Choosing gain resistors for op-amp circuits - Choosing current-limiting resistors for LEDs - Identifying the resistors on your bench - Working with register values and bit masks in firmware - Electronics hobby projects and learning circuits Quick answers for those "let me just calculate this" moments. Not complex enough for a full simulation, but you still want the result on the spot. EL tools supports your day-to-day electrical design work with simple, straightforward controls.

Screenshots

Resistor Code Calculators4 screens
EL tools4 screens

Verdict

The call

The clearest difference is ads: EL tools at none against Resistor Code Calculators's shown. EL tools also leads on update cadence (every 6 days vs every 7 months). Resistor Code Calculators's advantage is iOS requirement (13.4 vs 15.0). On price, in-app purchases and device support there is nothing between them.

Scored on Price ยท Rating ยท Positive reviews ยท Number of ratings ยท Update frequency ยท Ads ยท In-app purchases ยท Monetization ยท Best chart rank ยท Devices ยท Requires iOS

CostPrice ยท In-app purchases ยท Ads ยท Monetization

Both are free to download. Neither carries in-app purchases, so what you see is what you pay.

UpkeepUpdate frequency

Resistor Code Calculators ships an update every 7 months, EL tools every 6 days. The most recent releases landed on November 6, 2026 and November 13, 2026 respectively.

Scorecard3 real differences ยท 3 level
Resistor Code Calculators versus EL tools: the parameters behind the verdict, then further details
ParameterResistor Code CalculatorsEL tools
PriceFreeFree
Update frequencyEvery 7 monthsEvery 6 days โ€” better
AdsYesNo โ€” better
In-app purchasesNoNo
DevicesiPhone, iPad, iPodiPhone, iPad, iPod
Requires iOS13.4 โ€” better15.0
Further details โ€” not scored
Size6 MB8 MB
Age rating4+4+
DeveloperKanta KikuboKAZE Application

In-app purchases

None

Resistor Code Calculators

No in-app purchases

None

EL tools

No in-app purchases

Questions

Is Resistor Code Calculators free?
Resistor Code Calculators is free to download, with no in-app purchases.
Is EL tools free?
EL tools is free to download, with no in-app purchases.
Do Resistor Code Calculators or EL tools have ads?
Resistor Code Calculators shows ads; EL tools does not.
Which is updated more often, Resistor Code Calculators or EL tools?
Resistor Code Calculators ships an update every 7 months, and EL tools every 6 days. Most recently, Resistor Code Calculators was updated on November 6, 2026 and EL tools on November 13, 2026.

Other comparisons