EvolverFX AUv3 Audio Plugin vs NuRack Auv3 FX Processor

Evolver is a performance tool for creating multi-layered evolving sequences of sound. At its most basic think of evolver as a 4 lane sequencer which creates automatic accompaniment from notes and chords as you play on your MIDI keyboard, but it can also be used to create elastic evolving soundscapes where audio samples seamlessly merge into one another to create highly complex and original sounds. At the heart of evolver is a sophisticated wave synthesizer and sequencing engine which can create dramatic hard hitting transitions of sounds or merge sounds to create seamless transitions that evolve in time to the beat. It has 4 sequencer lanes which can run independently and mixed together using the real-time controls or over MIDI. When you play a chord on your MIDI keyboard for instance, each of the 4 sequencer lanes will take those MIDI notes and translate them into a musical sequence of sounds which are combined together and synced to create a form of automatic accompaniment. Evolver can load its own multi-layer patches or import them directly from Chameleon. These patches can be layered using the 4 sequencer lanes or split over a virtual keyboard. You can assign key zones, transpose them, assigned MIDI channels and velocity levels, set latch options etc. You can also load in your own one shot samples and lay them end on end to create evolving atmospheres or backing soundscapes. These samples can be looped or be free running with definable start/end and loop points using our non destructive editor. We also included a third sound source which lets you build sounds on the fly by overlaying harmonics to create anything from traditional sine, square, triangle, saw waves to complex detuned oscilators. These can be used in conjunction with multi-samples or one-shot-samples within the same sequencer lane. You can even randomize a complete sequence of harmonic sounds which when pieced together create some very unique and dynamic voices. Each sequencer lane can be up to 64 steps in length, each step has independent timing, pitch, volume, gate, probability, sample source etc. so the scope of what is achievable is vast. Each sequencer lane has its own ADSR, VCF and LFO which operates on all sounds within its lane, as well as being able to change the underlying settings for each sound source. Evolver also includes an ARP function which can be run in one of the default modes or you can define your own fingering patterns to be used to enhance your playing style. Create your own sequences, lay down your MIDI notes in your DAW and have Evolver automatically play along to your chord sequences, automatically locking to the host tempo. Sequencer events can be fixed or transposed allowing you to create percussive and drum backing using a single lane. Key Features: • 4 sequencer lanes • Up to 64 notes per sequence. • Each note can be fixed or transposed. • Timing and note probability. • 3 different sound source types (multi-sample, one-shot samples and harmonic) . • Add your own loops to a sequence. • Built in ARP function. • Import your own samples and mutli-sample patches. • Chameleon Support. • 5 different effect types (reverb, delay, phaser, flanger and chorus). • 8 band EQ. • .Latch Feature to hold chords/notes. • Create independent key zones with transposition and MIDI channels. • Paramter Automation from your DAW. • Control mixing and sequencer enable buttons using MIDI. • Built in Sampler. • Multiple Import options (including an experimental SFZ format). • iTunes and Files App importing of samples into the audio pool. • Files App Drag & Drop Support • Comprehensive Help pages included. Please Note: Not all features are currently compatible with Auria.

NuRack is an AUv3 based multi-channel audio and MIDI effects processor with a difference, it actually allows you to design your own custom effects using the 80+ building blocks provided. You have full control over routing which allows you to create complex audio paths in series or parallel. You can choose whether to use the stock interface or create your own custom interface using the built in Interface Builder which allows you to concentrate your audio components into a single customized effect. NuRack can run in one of two modes. The first providing 3 customizable effects racks which can be switched (manually or via MIDI), providing seemless switching (i.e. delay trails linger whilst another set of effects are faded in). The second mode allows you to route audio through 3 independent audio racks. A generaous number of over 80 audio and midi building blocks are provided covering 12 different categories of effects. Here are just some of those included in NuRack: Modulation Effects: Chorus, Flanger, Phaser, Tremolo, Vocal Doubler, TalkBox, UniVibe, Leslie & Vocoder. Time Based Effects: Stereo Delay, Tape Delay, Reverb and Reverse Delay. Spectral Effects: Parametric EQ, Graphic EQ, PitchShift, Auto-Pan, Bit-Crusher, Tube Overdrive, Distortion, Harmony, Harmonic Exciter and SlowMo. Dynamic Effects: VelocityControl, Compressor, Multi-Band Compressor, Noise Gate, Gate, and Limiter. Filter Effects: MultiFilter, LP/HP Filter, Frequency Splitter, MultiBand Splitter, Classic Filters, Formant Filter, Ring Modulation and Shelf Filter. MIDI Effects: MIDI Harmony, MIDI Velocity, MIDI Randomizer, MIDI Monitor, MIDI Mixer, MIDI Pads, MIDI Control, Strummer, MIDI Recorder, MIDI Modulation, MIDI Remap, CC Monitor, CC Generator, PitchBend, MIDI Time Clock, and ChordToMidi. Generator Modules: Noise, Audio Clip Launcher, SoundFont Player, Virtual Flute, Virtual Clarinet, Virtual Brass, FM Organ, FM Rhodes and Analog Sawtooth Synth. Automation: TouchPad, AutoMate, Pattern Automation, and Visual LFO. You also provide the ability to split and combine audio signal using splitters and mixer modules as well as a number of visual elements such as VU Meters, LED Meters, Scopes, Graphs etc. Some effects such as phaser and flanger are usually controlled by an LFO, but this can be detached and automated remotely. There are a number of modules that allow auomation based on direct touch (X/Y Pads), Visual LFO, Pattern Automation, MIDI input (CC data), or peak/rms level detection. These automation modules can remotely control knobs and sliders throughout your rack. Simply create a new rack and start adding modules to it. These modules are generally wired up automatically but these connections can be manually routed. Once you have your sound as you wish you can use it 'as is', or switch to Interface Builder mode where you can combine all your modules into a single interface. Elements can be dragged, dropped, resized and coloured as required. Add your own labels, image logos and custom backgrounds before saving your custom component. Use the X/Y Pad to control your modulation effects by detaching their LFO's. Use MIDI CC data to automate knobs. Use the velocity of an incoming signal to control the cutoff/resonance of a filter (wah) or volume level of a gain control (swell), as NuRack expands, so do the possibilities. Features: ○ Over 80 categorised modules. ○ 3 Input / Output busses supported. ○ Audio & MIDI effect. ○ Lots of audio & MIDI automation options. ○ Seemless transition between racks. ○ Manual audio path routing. ○ Open in presentation mode (auto hides controls). ○ Interface Builder to customize your rack. ○ AUv3 plugin runs in MIDI and none MIDI mode. ○ Add your own Text/Heading and Image/Logos and backgrounds to your design. ○ Compatibility options for DAW's not supporting multi-channels. ○ Dark/Light Modes Checkout the YouTube channel 'Paul the MusicMan' for demos and tutorials of NuRack.