BLEASS Dragonfly vs Textquencer Sequencer & Synth

BLEASS Dragonfly is a completely new approach to tremolo effect which brings new sonic possibilities to all music producers. Make your synths, voices or any melody “vibrate” in correspondence with its own frequencies, or with external basses and leads! Just like in Billie Eilish’s song “Xanny”, Dragonfly helps you achieve the same effect as when the voice gets modulated by a heavy bass. BLEASS Dragonfly automatically syncs the tremolo effect applied on a track using various triggers: First, you can use the pitch tracking module on either the input audio track (“self mode”) or a sidechained audio track (“sidechain mode”). You also can use the midi input to trigger Dragonfly with accuracy: the tremolo will automatically sync with the notes’ frequencies. Finally, a manual mode allows you to set a fixed frequency. Then you can finetune your settings by adjusting the fine, factor, smoothness, stereo, attack & release. The “Wild” mode applies a waveshaper to the signal to produce a subtle saturation. The final tremolo effect rate is mirrored by the flapping wings of the Dragonfly. BLEASS Dragonfly is also available for Mac & Windows (AU / VST3) https://www.bleass.com/dragonfly/ ________________________________________________ Technical description: SOURCE stage: - MANUAL: Tremolo rate is set by the Rate knob. Tremolo amplitude is set by the Amplitude knob. - MIDI: Tremolo rate corresponds to the rate of the lowest MIDI note received by the plugin. Tremolo amplitude corresponds to the velocity value of this note. - SELF: Pitch tracking on the input signal gives the tremolo rate. Tremolo amplitude matches the input signal’s amplitude. - SIDECHAIN: Pitch tracking on the sidechain signal gives the tremolo rate. Tremolo amplitude matches the sidechain signal’s amplitude. - SOURCE CHANNEL: Sets the channel to be analysed for SELF and SIDECHAIN modes. - AMPLITUDE: Sets tremolo amplitude in MANUAL mode. - GAIN: Sets the input gain in MIDI, SELF and SIDECHAIN modes. DRAGONFLY stage: - RATE: Sets tremolo rate in MANUAL mode. - FINE: Offsets the detected pitch value by +/- 0.5 semitone in MIDI, SELF and SIDECHAIN mode. - FACTOR: Detected or set rate is multiplied by this factor to give the final tremolo rate. - SMOOTH: Sets the smoothing duration of rate variations. - STEREO: Sets phase difference between left and right channels. - ATTACK: Attack duration of the effect. - RELEASE: Release duration of the effect. - MODE: SIMPLE is a basic tremolo. WILD uses complex waveshaping for warm and saturated effect. - WILDNESS: Sets waveshaping strength in WILD mode. - VISUALISATION: Dragonfly wings are animated to match the rate and amplitude of the effect. Green label on the left indicates the input MIDI note and rate. Blue label on the right indicates the applied MIDI note and Rate. MIX stage: - GAIN: Output gain of the effect. - DRY/WET: Dry/wet balance. NOTE: This is an AUv3 effect which needs a compatible host that ideally offers audio sidechain or MIDI FX routing (such as AUM, Cubasis 3 or Logic)

Textquencer is a text-based MIDI sequencer. Each letter's alphabetical index is mapped to the note in the scale you are working.  For example in C-major scale, Letter A (index = 1) is Note C (first note in the scale) Letter B (index = 2) is Note D (second note in the scale) Letter C (index = 3) is Note E (third note in the scale) Letter H (index = 8) is Note C but an octave higher and so on. You can create custom character mapping for emojis, punctuation, symbols or any letters in any language. A custom character can mapped to - A specific MIDI note or, - A specific note in the scale like the first note in the scale, the third note in the scale etc. Unless a character is custom mapped, a letter in English alphabet or a number, it will be a rest in the sequencer. Also, you can randomise the velocity and gate lengths in each step if you want, You can enable it on the settings menu and set a randomization min-max range. Please note that Textquencer is a MIDI app. The standalone version has an optional internal synth where you can enable or disable on the settings menu. The AUv3 plugin requires an audio app for output. For the AUv3 functionality, it needs to be hosted within an app such as AUM, Loopy Pro, Cubasis, Logic Pro, Nanostudio, Drambo, or apeMatrix.