Span Calc vs PileTrac Logger
Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.
Span Calc
Calculate maximum horizontal spans for wood joists and rafters using various lumber species and grades. Compares multiple options for common loading conditions based on NDS® standards.
- Calculates joist and rafter spans
- Supports all softwood and hardwood lumber
- Uses 2021 NDS® for Wood Construction
- Compares multiple species and grades
- Handles common loading conditions
Read full descriptionHide full description
The American Wood Council (AWC) Span Calculator for Wood Joists and Rafters (Span Calc) performs calculations for all species and grades of commercially available softwood and hardwood lumber as found in the 2021 National Design Specification® (NDS®) for Wood Construction. Joists and rafter spans for common loading conditions can be determined. A span options calculator allows selection of multiple species and grades for comparison purposes. Supported by the Softwood Lumber Board. Maximum horizontal spans for joists and rafters are calculated based on the following assumptions and conditions: · Joists and rafters are oriented to support vertical loads applied to the narrow (1.5 in. thick) face of the member, resulting in strong-axis bending. · At least three joists or rafters are installed parallel to one another and spaced not more than 24 inches on-center, with properly designed sheathing attached on the top (compression) edge of each joist or rafter. · Joists and rafters are single-span with adequate structural support at each end. The Span Calculator does not address cantilevered joists and rafters, multiple-span joists and rafters, or spliced joists and rafters. · For joists and rafters, most building codes specify a minimum bearing length of 1.5 inches on wood or metal and not less than 3 inches on masonry or concrete. These minimum bearing lengths are to be used in the absence of calculated bearing lengths. Consult the local building code for specific requirements. · Joists and rafters carry only combinations of dead load plus live load (D + L), dead load plus snow load (D + S), or dead load plus roof live load (D + Lr). The Span Calculator does not address wind load or seismic load. · Buildings in regions with ground snow loads greater than 70 psf should not use the prescriptive provisions of the governing building code without approval of the authority having jurisdiction. Buildings in these high snow zones should be designed in accordance with accepted engineering practice. While every effort has been made to insure the accuracy of the information presented, and special effort has been made to assure that the information reflects the state-of-the-art, neither the American Wood Council nor its members assume any responsibility for any particular design prepared from this Span Calculator application. Those using this Span Calculator assume all liability from its use.
PileTrac Logger
Read full descriptionHide full description
*Create full driven pile driving installation logs. Download for free and get 2 free trials (Once start is pressed that constitutes as 1 trial) before upgrading to a premium subscription to unlock full access. PileTrac Logger is a field tool that turns your phone's microphone into a real-time pile driving monitor. Accurately detect hammer blows, calculate stroke heights, and generate professional PDF reports — all without an internet connection. Built for pile driving inspectors, contractors, and geotechnical engineers, PileTrac Logger eliminates manual counting and paper logs so you can focus on the work happening in front of you. KEY FEATURES Real-Time Audio Detection Automatically detects each hammer blow using your device's microphone. No external hardware or sensors required — just press Start and let your phone listen. Automatic Stroke Height Calculation Calculates the hammer stroke height for every detected blow based on the time interval between impacts. Supports a built-in database of industry-standard pile driving hammers. Detailed Session Logging Tracks blow count, depth, stroke height, and timestamp at each depth increment. Expand any log entry to view individual blow-by-blow details. Hammer & Pile Database Select from a comprehensive database of diesel pile hammers. Choose from H-piles, pipe piles, square piles, octagonal piles, and circular piles with standard section sizes (AISC and EN standards). Bearing Capacity Estimation Quickly estimate nominal pile resistance using the Modified Gates formula (Rn = 1.75√E·log(10N) - 100) directly in the field. Input stroke height and blows per inch to get an instant result. Adaptive Sensitivity & Calibration Calibrate the ambient noise floor in seconds. Choose between auto-sensitivity or manually adjust the detection threshold with a simple slider to handle any jobsite noise condition. Professional PDF Reports Generate clean, well-formatted PDF reports that include project details, pile information, hammer specifications, and a complete driving log. Save directly to your phone's Downloads folder or share via email, messaging, or any other app on your device. Imperial & Metric Support Switch between US Customary (feet, kips) and Metric (meters, kN) units to match your project specifications. The entire app — including reports — adjusts automatically. DESIGNED FOR THE FIELD • 100% offline — no internet connection required • No account or login needed • No ads, no tracking, no data collection • Keeps your screen awake during active monitoring • Lightweight and fast — works on any modern device WHO IS THIS FOR? • Pile driving inspectors • Geotechnical engineers • Foundation contractors • Construction quality assurance teams • Civil engineering field technicians Download PileTrac Logger and bring accurate blow counting and stroke height calculations to your next job site.
Screenshots
Verdict
The clearest difference is in-app purchases: Span Calc at none against PileTrac Logger's 2. On price, ads, device support and iOS requirement there is nothing between them.
Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS
Both are free to download. PileTrac Logger sells 2 one-off in-app purchases. Span Calc asks for nothing beyond the download.
| Parameter | Span Calc | PileTrac Logger |
|---|---|---|
| Price | Free | Free |
| Rating | 3.0 (16 ratings) — better | — |
| Positive reviews | 29.6% of reviews | — |
| Number of ratings | 16 — better | — |
| Update frequency | Every 10 days | — |
| Ads | No | No |
| In-app purchases | No — better | Yes |
| Monetization | Free | — |
| Devices | iPhone, iPad, iPod | iPhone, iPad, iPod |
| Requires iOS | 14.2 — better | 15.0 |
| Further details — not scored | ||
| Size | 168 MB | 28 MB |
| Age rating | 17+ | 4+ |
| Developer | American Wood Council | Foundation Testing and Consulting, LLC |
In-app purchases
Span Calc
No in-app purchases
PileTrac Logger
- Premium Lifetime (Promo)$49.99
- Premium Lifetime$79.99
Questions
Is Span Calc free?
Is PileTrac Logger free?
Do Span Calc or PileTrac Logger have ads?
Other comparisons















