Pipe Calc Elite vs Pipe Trades Pro Calc

Pipe Calc Elite is the pipe trades calculator for pipefitters, plumbers, steamfitters, welders and sprinkler fitters. Solve simple and rolling offsets, take-outs and cut lengths in feet, inches and fractions, look up pipe data for seven materials, and work out pressure loss through pipe, valves and fittings. One purchase. No subscription, no ads, no account, and no data collected. Everything, including the full user's manual, works with no signal on the job site. On the App Store since 2013. OFFSETS AND FITTINGS • Simple and rolling offsets: offset, run, travel, roll and advance • Take-out and cut length for butt-weld long and short radius, field-cut, and threaded Class 150, 300, 3000 and 6000 elbows • Thread make-up by pipe size, or enter your own • Welder's gap, cutbacks, arc lengths and odd-angle fittings • Enter your own take-out when your fittings differ from the standard • When the fittings are longer than the centerline allows, the cut length shows how much you are short • Slope, grade, drop per foot and fitting angle PIPE DATA • Steel, Stainless Steel, Cast Iron, Aluminum, Brass, PVC and Copper, 1/8" to 42", with dimensions per ASME B36.10 and B36.19 and the ASTM copper and PVC standards • Schedules 10 to 160, Standard, Extra Strong and Double Extra Strong; stainless 5S to 160S; PVC Schedule 40, 80, 120 and SDR 21 to 41; copper Type K, L, M, DWV, Medical and ACR • Inside and outside diameter, wall thickness, internal area, volume per foot, and dry and filled weight per foot, with a cross-section drawing • Filled weight for water or any fluid density you set FLOW AND PRESSURE LOSS • Pressure loss by flow rate or velocity, per foot or over a run • Darcy-Weisbach with Colebrook-White friction • Ten valves and fittings, with loss coefficients from the ASHRAE Handbook by size and by threaded or welded joint • Water temperature from 32 to 212°F sets the viscosity • Answers in psi, psf, feet of head, inches of mercury, kPa and bar, with the Reynolds number and friction factor used • Flow, velocity, force, pressure and area solved from each other CALCULATOR AND CONVERSIONS • Add, subtract, multiply and divide feet, inches and fractions, down to 1/64, with meters and millimeters mixed in • Areas and volumes carry their units: 5 in x 5 in is 25 square inches • Conversions for length, area, volume, weight, flow, velocity, pressure, force and temperature • Sine, cosine, tangent and their inverses, degrees-minutes-seconds, powers and roots, and percent • Store values and recall them later, even after the app is closed The full user's manual, with worked examples, is built in: hold Offset, Convert or any other function key to open it at that key's section. Technical support is free. If you have questions, suggestions for improving this app, or find a bug, please email us at techsupport@cyberprodigy.com and we will respond as soon as possible. Pipe Calc Elite™ is not associated with Pipe Trades Pro™ and Cyberprodigy LLC is not affiliated with Calculated Industries, Inc.

FREE Try Before You Buy trial, your App Store account is not charged by Apple during the free trial. Welcome to Pipe Trades Pro for iPhone, a game-changing tool for professionals in the pipe trades industry. This application is expertly designed to enhance the efficiency and accuracy of pipefitters, steamfitters, sprinklerfitters, and welders. From complex calculations to extensive pipe data, Pipe Trades Pro is your go-to solution for a streamlined work process. ----- ADVANCED CALCULATION CAPABILITIES ----- • Tackle complex measurements like cut lengths, take-outs, and odd-degree fittings easily • Navigate through right angles, offsets, and intricate rolling offsets confidently • Utilize tools for determining pipe areas, fill weights, and unit conversions • Efficiently manage parallel pipe cutbacks with accurate alignment and spacing • Incorporate feet-inch-fractions and trigonometry for precise measurement adjustments ----- FLUID DYNAMICS AND PRESSURE ANALYSIS ----- • Accurately compute flow rates, velocity, force, and volumes for diverse fluid types • Assess pressure loss effectively across any pipe size, type, or distance • Make informed decisions based on dynamic fluid properties and behaviors • Optimize piping systems for maximum flow efficiency and safety ----- COMPREHENSIVE PIPE DATA ACCESS ----- • Access vital information for pipes up to 42 inches, including diameters and wall thickness • Select from materials like steel, stainless steel, brass, aluminum, etc. • Quickly reference internal area and filled weight per foot for different pipe types • Make informed choices with extensive material and dimension options ----- USER-CENTRIC INTERFACE DESIGN ----- • Experience a streamlined, intuitive interface designed for quick and easy navigation • Access key features with minimal taps, saving time and enhancing user experience • Benefit from an interface that optimizes the iPhone’s screen space and usability • Enjoy a clutter-free, visually appealing layout for stress-free operation • Adapt quickly with an interface designed for both new and experienced users ----- OFFLINE FUNCTIONALITY AND SUPPORT ----- • Utilize full app capabilities without an internet connection, perfect for on-site tasks • Access all data and features offline, ensuring uninterrupted productivity • Rely on consistent app performance in remote or internet-challenged locations • Receive dedicated customer support for any queries or technical issues Pipe Trades Pro for iPhone is not just an application; it's a comprehensive tool transforming how pipe trade professionals work. It combines advanced technology, user-friendly design, and practical features to create a smoother, more efficient workflow. Embrace the future of pipe layout and design with Pipe Trades Pro, where accuracy meets efficiency. SUBSCRIPTION INFORMATION Your Free Trial period is free of charge. Subscriptions offered will automatically renew at the end of the chosen period. Payment will be charged to your Apple account upon purchase confirmation. The subscription will automatically renew unless auto-renew is turned off or the subscription is canceled in settings at least one day (24 hours) before the subscription period ends. You can manage your subscription and turn off auto-renewal in your Apple account Settings > Subscriptions. LEGAL Pipe Trades Pro is a trademark of Calculated Industries, Inc. Copyright 2025