Pipefitter_Pro vs Pipe Offset Calculator!

Pipefitter Pro is a calculator for pipefitters. It calculates offsets, elbow angles and spool lengths, and draws what it works out. Choose a case from the menu, enter the pipe diameter and elbow radius on the workshop keypad, then read the available results: angles, the spool between elbows, elbow takeout, arc lengths and caliper dimensions. CASES AND VIEWS • BACK TO BACK — two elbows, with either the angle or the offset unknown. • S TYPE — offset, travel or a fixed 45° option. • TEE OFFSET — calculations that include the branch diameter. • CALCULATOR — one elbow cut out of a 90°. • 3D — two elbows in space, set using the A, B and C dimensions of a box. • SLIDER / SLIDER S TYPE / SLIDER TEE — change the angle and watch the offset change. • 3D SLIDER — set the elbow orientation in a spatial model and read the angles, the insert and the live box dimensions. The box is a visual reference, not a cut length. Depending on the case, results appear on the Angle, Dimensions and Elbow tabs; selected cases add a 3D view you can rotate and zoom. UNITS AND INPUT Lengths in millimeters, centimeters and inches. Feet-and-inches notation and decimal or fractional inches are also supported. Choose 1/16 or 1/32 precision for inch fractions. Angles are given in decimal degrees. The workshop keypad and fraction picker help you enter dimensions; add frequently used cases to favorites. PIPE AND ELBOW DIMENSIONS The DIMENSIONS tile opens the built-in NPS/DN table. It contains outside diameters and centerline radii for long-radius and short-radius elbows. Add and edit dimensions, then use them in calculations. Save a list backup to a file and restore the list from a backup. BEFORE YOU CUT Pipefitter Pro supports the preparation of workshop work. Check the dimensions against your technical documentation and your shop procedures before cutting and welding.

Pipe Offset Calculator gives pipefitters, plumbers and electricians the numbers they cut to: rolling offsets, fitting takeouts and the end-to-end cut, flange bolt-up, conduit bends and drainage grade, in big type on a fraction keypad that works in sixteenths. ROLLING OFFSET Enter the set (or rise) and roll, pick your fitting angle — 22½°, 30°, 45°, 60°, 90°, or any custom angle — and get true offset, travel and run instantly, with a labeled diagram so you always know which number is which. SIMPLE OFFSET Single-plane offsets: one measurement in, travel and run out, drawn to your actual fitting angle. FITTINGS — THE FITTER'S CUT • Cut — pick the pipe size (1/2″ to 24″), the fitting on each end (90° LR, 45° LR, 90° SR, tee, a 90 cut to any angle, or your own takeout) and the welder's root gap, then enter the travel: the end-to-end cut comes out with both takeouts and both gaps already off. Pull the travel straight from the Rolling or Offset tab in one tap • Elbow — cut a 90° long-radius elbow to any angle: the takeout, and the heel, side and throat marks measured from the end you keep • Bolt-up — Class 150 and 300 raised-face flanges: stud count and diameter, stud length, and the wrench for the heavy hex nut • Tables — butt-weld takeouts for 90° LR, 45° LR, 90° SR and tees up to 24″, and a sixteenths decimal-to-fraction table Every takeout and stud number comes from a published catalog to ASME B16.9 / B16.5 and is checked row for row against a second, independent source. CONDUIT BENDING The hand-bender math for EMT, on one tab: • Offset — bend angle 10° to 60°, distance between bends and shrink, and where the first mark goes • 3-bend saddle — centre and side marks over a pipe or beam, 45° or 60° centre • 4-bend saddle — all four marks over an obstacle of any width • 90° stub — mark from the end by conduit size, with back-to-back stubs Every result shows the bender-table number and the exact trig beside it, so you know what the rounding cost. GRADE Drainage slope both directions: run + grade gives you the drop, or run + drop gives you the exact grade — in inches-per-foot and percent, with one-tap presets for 1/8″, 1/4″ and 1/2″ per foot. BUILT FOR THE JOBSITE • Every measurement works both ways: feet-inches-sixteenths AND decimal inches — enter either, read both • Custom fraction keypad with 1/16″ steps and ±1/16″ nudge buttons • Big result cards — tap any result to copy it • Save any result; your saved numbers are one tap away on every tab • One-handed layout, haptic feedback, light and dark • Works offline — in the basement, the crawlspace and the parking garage Buy it once, use it every day.