Shaft Alignment Calculator vs Wari
Price, ratings, monetisation and update history for both apps, side by side ā with what reviewers say about each.
Shaft Alignment Calculator
Read full descriptionHide full description
During shaft alignment of rotating machinery, this app calculates the required shim amounts for the front and rear feet, as well as the horizontal adjustment direction and distance, based on 4-point Rim and Face dial indicator readings. Furthermore, if the alignment can be brought within your custom "Tolerance" limits by adjusting only one set of feet (front or rear), the app automatically simulates and displays the "Optimal Shim Amount," "Adjustment Range," and "Predicted Residual (Remaining Misalignment)." --- Key Features --- [NEW] Reverse Indicator Method Support Fully supports the Rim-Rim reading method on both sides of the coupling. Includes a dedicated input screen with automatic compensation for Bar Sag values. Enter the distances using the stationary indicator position as the starting point (0). [NEW] Single-Foot Adjustment Simulation Enter your Rim and Face tolerances in "Settings". If the alignment can be fixed by moving only the front or rear feet, it automatically suggests the optimal shim amount, acceptable adjustment range, and the resulting residual misalignment. (*If the tolerance is set to 0, single-foot adjustment suggestions will not be displayed.*) [NEW] Custom Tolerance Settings Freely set and modify Rim and Face tolerance values to match your specific site standards. [NEW] Alignment Visualizer (Windows Only) Graphically displays the alignment status based on calculation results. ⢠Memory Function Input values are retained even if you close the app halfway through. ⢠Calculation History Saves up to 30 recent calculation results, automatically overwriting the oldest entries. ⢠Save Measurement Records Save the final, in-tolerance Rim and Face readings along with the Machine Name and Gap distance (up to 30 records). ⢠Face (+/-) Toggle Press the "+=" button to easily switch between "+ = Closed" and "+ = Open" for Face gauge readings. ⢠Offset Function Enabling this displays input fields. Enter values in the desired offset direction, and they will be reflected in the calculation. ⢠Average Mode Enabling this adds extra Rim/Face input fields. The app will calculate based on the average of two measurements. (*Not available in Reverse Indicator mode.*) ⢠Swap Gauge Setup Turn this ON if your dial indicators are set up to read from the Driven machine to the Motor. (*Not available in Reverse Indicator mode.*) ⢠Dark Mode Ensures optimal visibility in various environments, whether indoors or outdoors. --- App Highlights --- ⢠Lightweight operation without complex animations, preventing unnecessary battery and memory drain. ⢠Fully standalone application; works perfectly in underground facilities or deep inside plants without an internet connection. --- Specifications --- ⢠"Left/Right" in the app refers to the direction when looking from the motor toward the driven machine. ⢠Enter Coupling Diameter (or Gauge Span for Reverse mode) and Front/Rear distances in mm. Enter Rim, Face, and Bar Sag values in hundredths of a millimeter as whole numbers (e.g., enter 15 for 0.15 mm). ⢠For inch/mil (thou) calculations, enter Coupling Diameter and distances in inches. Enter Rim, Face, and Bar Sag values in mils/thou as whole numbers (e.g., enter 5 for 5 mils). --- How to Use --- 1. Enter the machine dimensions. 2. Enter the 4-point measurement readings. 3. Check the "+=" button setting (*Rim-Face method only*). 4. Tap the "Calculate" button. ---
Wari
Read full descriptionHide full description
Wari-Tsuke is a focused layout and mark-out tool for field work: carpentry, interior finish, tile, hardware mounting, railings, fences, partitions, and framing. Enter the total width, the part width, and the number of parts, then choose Equal Gap (even gaps between parts) or Center Spacing (even center-to-center pitch). The app shows exactly where to mark from the left edge, so you can pull every mark straight from a tape. It works in millimeters, decimal inches, and fraction inches, with 1/16, 1/8, or 1/4 inch rounding. Values snap to the chosen graduation, the leftover remainder can go to the ends or be spread evenly, and the mark-out list keeps the last mark dead-on at the real span. Marking Mode turns the list into a full-screen electronic story pole: one cumulative position at a time, large and clear, with check-off as you go. Field Copy bundles the inputs, the result, and the mark-out positions into one copy you can share with your crew. Building-code opening checks (for example the 4-inch guard / 110 mm baluster clear opening) are included as an optional support feature. They are off by default, the standard (US / JP / EU) is switchable, and they do not replace local code judgment. No account, no cloud sync, no ads, and no analytics. Everything runs on-device and works offline.
Screenshots
Verdict
The clearest difference is price: Wari at Free against Shaft Alignment Calculator's $5.99. Shaft Alignment Calculator's advantage is iOS requirement (13.0 vs 15.0). On ads, in-app purchases and device support there is nothing between them.
Scored on Price Ā· Rating Ā· Positive reviews Ā· Number of ratings Ā· Update frequency Ā· Ads Ā· In-app purchases Ā· Monetization Ā· Best chart rank Ā· Devices Ā· Requires iOS
Wari is free to download; Shaft Alignment Calculator costs $5.99 up front. Neither carries in-app purchases, so what you see is what you pay.
| Parameter | Shaft Alignment Calculator | Wari |
|---|---|---|
| Price | $5.99 | Free ā better |
| Update frequency | Every 2 days | ā |
| Ads | No | No |
| In-app purchases | No | No |
| Devices | iPhone, iPad, iPod ā better | iPhone, iPod |
| Requires iOS | 13.0 ā better | 15.0 |
| Further details ā not scored | ||
| Size | 20 MB | 19 MB |
| Age rating | 4+ | 4+ |
| Developer | Eiji Shinohara | KENTA OSAWA |
In-app purchases
Shaft Alignment Calculator
No in-app purchases
Wari
No in-app purchases
Questions
Is Shaft Alignment Calculator free?
Is Wari free?
Do Shaft Alignment Calculator or Wari have ads?
Other comparisons















