Comparison

Pipe Craftsmen vs GearTech OS

Price, ratings, monetisation and update history for both apps, side by side — with what reviewers say about each.

Head to head
About

Pipe Craftsmen

Features
Read full description

Pipe Craftsmen is the pipefitter's toolbox: the numbers you work to, in the tape's own language, with every dimension copied from the published tables and every drawing showing where the number runs on the steel. THE SPOOL Build a spool piece by piece - pipe, fittings, valves, field welds - branching at a tee. Add an offset the way you measure it, run and offset, or a rolled one with its roll; the elbows go in by themselves, stock 45s or a 90 cut down to the odd angle. Lay an equal spread beside it. Read the drawing as an iso, a plan or any elevation, put the ruler on a pipe or on a whole line from turn to turn, and get the cut list: every cut less the fittings, every weld counted. THE RULER One pipe with any fitting or valve at each end: set it by the length you know and read between any two points - centers, faces, pipe ends, the throat or the heel. THE ISOMETRIC Draw a run leg by leg, or sketch it with a finger on the grid. Turn the compass, swipe between the iso, the plan and the elevations. With the bender attached, every turn becomes a bend: the tube to cut, each bend's angle and centerline mark, and the roll between bends. THE CALCULATOR Feet, inches and fractions natively - 5'-6" + 3'-9" reads back 9'-3". Metric keys, angle mode with decimal and DMS entry, store and recall shared across every keypad in the app, session history, and your starred measurements one tap from the display. THE FITTINGS REFERENCE Every dimension of every fitting, from the published tables: butt weld, socket weld, threaded, flanges, grooved, copper, no-hub cast iron and PVC. Every page draws its fitting in section with the selected takeoff dimensioned on the steel. Set your root gap, socket pull-back, thread make-up, grooved separation and no-hub stop once; every takeoff in the app follows. The Fitting Finder searches the whole set without leaving the calculator. THE TOOLS - Pipe Offset, plain or rolled: solve the triangle, then the fitting each end needs, the pipe between and its weight - Triangle: any two facts of the right triangle, the rest solved and drawn - Equal Spread: the advance that keeps parallel lines parallel through a turn - Miter Joints: cut angle, cutback, and the blank drawn flat on the bench - Fitting Cutdown: a 90 cut to any angle, with the three arcs to mark - Rolled Olet: set a roll angle with a tape measure - Tube Bending: one bend, a run of bends, or a run drawn as an iso - Pipe Information: bore, wall, circumference, the weights you rig by, and the water it holds - Abbreviations: what the letters on a print mean SHARE IT Send a spool, run or ruler to your partner as a file; a tap opens it on their phone, figured the way you figured it. Export everything at once to a new phone. IN YOUR POCKET Built for a phone held one-handed on a rack: big keys, answers that read at arm's length, and everything working without a signal. On an iPad the pages open out. PRO The calculator, pipe information and a selection of fittings in every connection are free. Pro opens the rest: a monthly or yearly subscription, or a lifetime license bought once that never renews. Terms of Use: https://pipe-craftsmen.com/terms-of-use Privacy Policy: https://pipe-craftsmen.com/privacy-policy

About

GearTech OS

This app provides specialized calculation tools for various trades, including pipefitting, welding, electrical, and HVAC. It displays all calculations with step-by-step math and 3D diagrams, working offline and offering bilingual support.

Highlights
  • Trade-specific tools
  • Step-by-step math explanations
  • 3D diagrams and visualizations
  • Offline functionality
  • Bilingual support (English/Spanish)
  • Crane hand signals in 3D
  • Flange bolt-up torque calculations
Features
Read full description

GearTech OS replaces the box of single-purpose calculators in your truck with one app built for the trades — by someone who works them. Pick your trade and get tools made for it: pipefitting, welding, electrical, framing, concrete, HVAC, plumbing, machining, solar, sheet metal and automotive. No pipe jargon cluttering the electrician's screen, no electrical keys on the welder's — each trade gets its own tools and its own keypad shortcuts. FREE, AND PRO. The calculator is free forever — offsets, cut length, take-off, rolling offset, miter and weld gap — and every trade also keeps some of its own tools open with no subscription. GearTech Pro opens the rest of the tools for your trade, with one month free to try it. No account needed either way. SPOOL / ISO. Dictate or type the dimension chain off the drawing and the app echoes back what it understood, draws the isometric with a balloon on every piece, and gives you the cut for each length of pipe and the bill of materials. Save the spool by name and open it again. EVERY result shows the math. Tap "Show math" under any answer to see the formula, your numbers plugged in, and the result. Learn it, trust it, and check your work in the field. REAL diagrams. Every tool draws what you're building — a 3D rolling offset box, a butt-weld elbow you can cut to a custom degree, a saddle/fishmouth, a reducer cone, roof rafters, conduit fill, ducts, gears and more. NEW — CRANE HAND SIGNALS IN 3D. 22 ASME B30.5 signals. The signal person gives the signal and the crane performs the motion, with the load always plumb. Spin the camera and watch it from wherever you have to stand. NEW — FLANGE BOLT-UP. Target-stress torque by bolt size, material, lubricant and percentage of yield, with the 30/60/100% passes worked out and the tightening order drawn for 4 to 32 bolts. Built for pipefitters and welders first: - Pipe offsets, rolling offsets, fishmouth/saddle templates, miters, trunnions, reducers (concentric & eccentric), and ASME B16.9 fittings with custom degrees - Spread/line banks, slope/grade, thermal expansion - Crane hand signals in 3D and flange bolt-up torque - Constants cheat-sheet and a 272-question practice EXAM for the NITC / UA STAR, including crane signal person — every question explained step by step, and the app remembers what you missed Plus 100+ tools across 10 more trades: - Electrical: voltage drop, conduit fill (NEC), box fill, ampacity + derating, motor FLC, 3-phase power, stub-up take-up - Framing: rafters, hip/valley/jack, stairs, pitch, baluster spacing, board feet - Concrete: slab/footing/column volume, bags, rebar, blocks - HVAC: tonnage, CFM, duct sizing (round & rect), friction rate, sensible BTU - Plumbing: drain slope, DFU, fixture units to GPM, pipe sizing, gas pipe - Machinist, Solar, Welding, Sheet metal, Automotive Works 100% offline — the 3D included. No account, no ads, no tracking. Your settings, cut lists and memories stay on your phone. Bilingual: English and Spanish, switch anytime. We build the world around us. Our tools should be built for us. — Per Diem Syndicate

Screenshots

Pipe Craftsmen4 screens
GearTech OS4 screens

Verdict

The call

The clearest difference is in-app purchases: GearTech OS at none against Pipe Craftsmen's 3. GearTech OS also leads on update cadence (every 5 days vs monthly). On price, ads, device support and iOS requirement there is nothing between them.

Scored on Price · Rating · Positive reviews · Number of ratings · Update frequency · Ads · In-app purchases · Monetization · Best chart rank · Devices · Requires iOS

CostPrice · In-app purchases · Ads · Monetization

Both are free to download. Pipe Craftsmen sells 3 in-app purchases, starting at $5.99 per month. GearTech OS asks for nothing beyond the download.

UpkeepUpdate frequency

Pipe Craftsmen ships an update monthly, GearTech OS every 5 days. The most recent releases landed on November 10, 2026 and November 18, 2026 respectively.

Scorecard2 real differences · 8 level
Pipe Craftsmen versus GearTech OS: the parameters behind the verdict, then further details
ParameterPipe CraftsmenGearTech OS
PriceFreeFree
Rating—5.0 (10 ratings) — better
Positive reviews—100.0% of reviews
Number of ratings—10 — better
Update frequencyMonthlyEvery 5 days — better
AdsNoNo
In-app purchasesYesNo — better
Monetization—Free
DevicesiPhone, iPad, iPod — betteriPhone, iPad
Requires iOS15.0 — better16.0
Further details — not scored
Size32 MB4 MB
Age rating4+4+
DeveloperVICTOR DIGITAL TOOLS LLCJosue Ponce

In-app purchases

3 purchases

Pipe Craftsmen

Subscriptions2
  • Pipe Craftsmen Pro Monthly1 Month trial$5.991 Month
  • Pipe Craftsmen Pro Annual1 Month trial$39.991 Year
One-time1
  • Pipe Craftsmen Pro — Lifetime$119.99
None

GearTech OS

No in-app purchases

Questions

Is Pipe Craftsmen free?
Pipe Craftsmen is free to download, with in-app purchases available.
Is GearTech OS free?
GearTech OS is free to download, with no in-app purchases.
Do Pipe Craftsmen or GearTech OS have ads?
Neither Pipe Craftsmen nor GearTech OS shows ads.
Which is updated more often, Pipe Craftsmen or GearTech OS?
Pipe Craftsmen ships an update monthly, and GearTech OS every 5 days. Most recently, Pipe Craftsmen was updated on November 10, 2026 and GearTech OS on November 18, 2026.

Other comparisons