Bend Master vs Pipe Offset & Cut Length

Bend Master is the essential conduit bending calculator and angle gauge for electricians, plumbers, and DIYers. Measure angles with your iPhone's sensors, calculate precise bend marks in seconds, and save camera-measured results — all in one professional tool. BEND CALCULATORS THAT GET IT RIGHT • Offset — Enter your conduit size, angle, and obstacle height. Get exact shrink, spacing, and mark points with a step-by-step diagram. • 3-Point Saddle & 4-Point Saddle — Instantly calculate bend marks, rotation, and fit for crossing obstacles. No more guessing on the job site. • 90° Stub-Up & 90° Back-to-Back — Get take-up, mark spacing, and stub height for perfect corners and offsets between two surfaces. • Compound 90° (Circle, Square & Rectangle) — Master tight corners around round, square, and rectangular obstructions with exact mark spacing, take-up, and arc length. SMARTPHONE ANGLE GAUGE • Real-time roll, pitch, and horizontal line angles using the built-in motion sensors. • Bubble level view for quick flat-surface leveling. • One-tap zero calibration and angle reset for accurate relative measurements. CAMERA ANGLE OVERLAY • Point your camera at any surface to measure angles in real time. • Capture photos with angle overlays embedded, perfect for documenting measurements and sharing with your crew. WHY BENDMASTER • Clear visual diagrams that show exactly where to mark and bend. • Conduit-specific formulas with proper shrink and multiplier handling. • Save or share any diagram as an image for job-site reference. • Haptic feedback and a distraction-free dark interface for job-site use. • Bend calculations work offline — no internet needed for calculations in the field. BendMaster Premium unlocks all bend types — Offset, 3-Point & 4-Point Saddles, 90° Stub-Up, 90° Back-to-Back, and Compound 90° bends — plus the camera angle gauge. Download now and take control. Premium is available as a one-time in-app purchase for lifetime access to all bend calculation tools and the Camera Angle Gauge. No recurring subscription is required. Use Restore in the app to restore your purchase. Terms of Use: https://www.apple.com/legal/internet-services/itunes/dev/stdeula/ Privacy Policy: https://61e557ea.bends.pages.dev/privacy-policy

Rolling offsets, solved before you cut. Pick the fitting and the size, type what you measured, and you get the cut length with the takeoff (Z in the standards) already subtracted from both ends. Mark the pipe and cut it. ■ If it will not go together, you hear it first A positive number does not mean it can be assembled. When the socket depths would overlap, the app finds it before you cut and shows what does fit — a fitting with a smaller angle, or one size down. ■ Offsets that move in two directions For a rolling offset, the app separates true offset, run, travel (center to center) and the roll angle. It works at 22.5° and 11.25° as well as 45°, and when the run you have is fixed, it can solve for the angle instead. ■ Every number carries its source Welded fittings use the bend radius R = 38.1 x nominal size (inch) with ASME B16.9 for the 45° center-to-end; PVC DWV uses the published fitting dimensions. Japanese standards (JIS K 6739 / K 6743 / K 6777, JIS B 2301) are there when you switch regions. Tap the info button next to the answer to read where a number came from. ■ Elbows that aren't built in: measure and add them Measure an elbow once and register it, and every calculation after that uses its actual dimensions. Thread engagement can be adjusted per size, one thread at a time. ■ Keep it per job, hand it over on paper Add an answer to a job and it becomes a table: piece number, cut length, fitting, roll angle. Export it as a PDF or CSV. Register a fitting and the numbers on the paper are recomputed too. ■ Works with no connection Everything is computed on the device. Job records stay on this device only — they are not stored in iCloud, so they cannot move to a new phone. What leaves the device is your support messages, plus anonymous usage statistics and crash diagnostics (Firebase Analytics / Crashlytics). ■ About pricing Cut length for a straight run between two fittings, the 45° offset in one plane, the 78 bundled fittings and the welded formula are free, always. Rolling offsets, 22.5° and 11.25°, solving for the angle, your own measured fittings and thread engagement, and job cut lists (PDF/CSV) are Pro. There is a one-time purchase, or monthly and yearly plans. ■ Units and standards Switch between inch (ASME, North America) and mm (JIS, Japan). In North America the fittings become ASME B16.9 (welded) and PVC DWV, and the 45° center-to-end is read from the published table. What the app shows is a guide for installation. The final call belongs to the job's own standards and a licensed fitter. The app does not reproduce standards documents or manufacturer catalogues — it cites the number and name of the standard, the maker and the revision, and computes dimensions from published values and formulas. Monthly and yearly plans renew automatically. You can cancel in Settings > your name > Subscriptions on your iPhone. The one-time purchase does not renew. Terms of Use: https://rainbowtree.work/app/terms Privacy Policy: https://rainbowtree.work/privacy/haikan-kirisunpo.html