Hearing Analyzer Portrait vs Tonelog Hearing Test

"Hearing Analyzer Portrait" is a hearing health check tool that allows you to measure your hearing over a very wide range of audible frequencies. The human ear possesses an auditory range from 20Hz to 20kHz. However, conventional hearing tests (125 Hz to 8 kHz) cannot assess the low-frequency or high-frequency bands. This app covers nearly the entire audible range, allowing you to self-diagnose your hearing ability. By measuring your current hearing characteristics, try to consider the wellness of your ears and the way of natural sound reproduction. This app employs an intuitive and simple testing method, enabling hearing characteristics to be measured in a very short time. It performs hearing tests within the audible range by detecting the minimum volume setting at which pure tones can be heard. Recommended to check your own hearing ability on a daily basis for the audiophile, music players, sound professionals and all music lovers. See if you have golden ears! Features: - Broadband hearing test in 3 frequency bands: LF (Low Frequency) - 30Hz to 100Hz, STD (Standard Frequency) - 125Hz to 12kHz, HF(High Frequency) - 13kHz to 20kHz - Test tones of LF: 30, 40, 50, 60, 70, 80, 90, 100 (Hz) - Test tones of STD: 125, 250, 500, 1k, 2k, 4k, 8k, 12k (Hz) - Test tones of HF: 13k, 14k, 15k,16k, 17k, 18k, 19k, 20k (Hz) - Test channel: Left, Right - Test tone type: Intermittent tone (Tone A) / Continuous tone (Tone B) - Measurement result graph display (Level/Ath/Both): Linear level without ATH compensation (Level), ATH compensation (Ath)[*1], Both results (Both) - Clear setting and results. (Reset) - Snapshot of single band result. (Snap) - Snapshot of full band result. (Snap-W) *1: ATH (Absolute Threshold of Hearing) ATH is also known as the hearing threshold and is the minimum sound pressure level of pure tone that can be detected on the hearing in noise-free environment. Human is said to be able to listen from 20Hz to 20kHz, but the sensitivity of the hearing will vary greatly depending on frequency. ATH varies with age and sex, but is a good sensitivity at mid-range (1kHz - 5kHz), and needs more greater sound pressure level at a lower and higher frequency. In the LF and HF frequency bands, the information in the ATH graph is for reference only. Note: - This app does not support all wireless headphones and only supports Bluetooth (A2DP) headphones. If you cannot confirm the connection, use wired headphones. AirPods products are not support due to specialized digital signal processing performed internally. - This app generates a test tone signal with a high gain, so please special attention to the volume adjustment. - Before the diagnosis start, please set the hardware volume control to the central position of 50%. If you move the volume slider upward, the output volume will have a large gain. So as not to be excessively large gain for your ears, please adjust it carefully.  - The classification of the hearing ability refers to WHO. Remarks: In general, a high risk of hearing loss has been known if you continue to hear the sounds of a high acoustic pressure level, such as, listening of the portable audio and working with too loud noises. We hope that you will continue to take an interest in your hearing health on a daily basis through this app. If you feel the need to manage the health of your ear, it is recommended that you see a medical professional. Disclaimer: This app is not intended to be used for a medical purpose. This app is not intended to diagnose, prevent, monitor, treat, alleviate or compensate a disease, an injury, a disability or a handicap. If you think you have hearing problems, please consult with your doctor, or other qualified healthcare professional. Please use this app at your own risk. TOON,LLC don't take any responsibility for direct or indirect damage that could result from its use. Please visit our support site for more information.

A pure-tone hearing test that checks both ears in about three minutes, with the headphones you already own. Most hearing apps play a handful of tones and hand you a verdict. This one measures your threshold at seven frequencies in each ear, from 125 Hz to 8 kHz, plots them on a real audiogram, and prints the conditions the numbers were taken under so you know how much to trust them. We check your setup before we measure Your result depends on your headphones and on how quiet the room is. Before a single tone plays, the app confirms headphones are connected, recognises the headset, asks you to set the volume between 70 and 90 percent, and measures how loud it is around you right now. If something is off, it says so instead of pretending. What you get • Know how you hear at every pitch — seven frequencies, one ear at a time • Read a real audiogram, not a score — the chart shape a clinic actually uses • See your hearing age as a range, next to your own age group • Track change over time — two tests on one chart, frequency by frequency • Hand over a one-page PDF instead of a screenshot of your phone How the test works Put on any headphones, find a quiet room, and tap the moment you hear a tone — even a faint one. The app works one ear at a time and steps down in level until it finds the softest tone you can still hear, at 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz and 8 kHz. Some presentations are silent on purpose, so guessing shows up as guessing. At the end you get an audiogram with the right ear drawn as O and the left as X, a reliability grade, and a plain-language read of each ear. Honest about its own limits An iPhone is not an audiometer and consumer headphones are not calibrated, so every scale in the app is labelled estimated dB HL (uncalibrated). Every saved result carries the headset, the volume, the room-noise reading and the date beside it. The app will not run the test through the phone speaker, because a level nobody knows is not a measurement. Everything stays on your iPhone No account. No sign-up. No upload. No ads. Nothing you measure leaves the device, and the test itself needs no network connection at all. The microphone is used for one thing only — measuring how loud the room is before the test — and no audio is recorded, saved or sent anywhere. You can delete every stored result from Settings. Not a medical device Hearing Test is a screening tool. It is not a medical device, it does not diagnose, treat or monitor any condition, and it does not replace an examination by an audiologist or physician. Results are an estimate produced with uncalibrated equipment in an unknown room. If you have ear pain, a sudden change in hearing, ringing that will not stop, or any concern at all about your hearing, see a qualified professional. At best this app gives you a dated audiogram and a reason to book that appointment. What you need • Any headphones — AirPods, wired earbuds or over-ears • A quiet room • About three minutes