VTconsole

January 1, 2024

* iOS 17 support * An error regarding dark mode appearing has been corrected.

December 5, 2020

- An error regarding the collaboration with VTconsoleAssistant has been corrected. - Application cursor mode setting added.

November 28, 2020

An error regarding the collaboration with VTconsoleAssistant has been corrected.

October 19, 2020

- iOS 14 support - Enhanced barcode reader - Pinch gesture corrections in font setup

January 13, 2020

- iOS 13 support: Dark mode - In-App purchase module „Site Survey“ removed since this functionality is not permitted anymore by Apple since iOS 13. - „Bracketed past mode“ supported, see https://cirw.in/blog/bracketed-paste. - Stability enhancements.

May 2, 2019

Bugfix: Keyboard handling

November 6, 2018

- In-App purchase module „Site Survey“ enhanced. - iOS 12 support. - iPhone Xr, Xs, Xs Max support.

May 10, 2018

New: - In-App purchase module „Site Survey“. This module can be used as a monitor that identifies WLAN radio coverage problems. In parallel to the telnet host screen the current IP address and SSID along with BSSID (access point) and bitrate are shown in a small table and recorded in a logfile. - Switch „Automatic reconnect“. If enabled a eventually broken host connection will be automatically re-established, without any query. - The standard iOS status bar is enabled in portrait modus for devices with a display size greater than 4 inch. - iOS 11 support. - iPhone X support. - Linea Pro / Infinea Library update to version 2.2 of Jan. 11, 2018. Bugfix: - The font „Monaco“ is working again. - Enhanced stability.

May 3, 2017

New: If a barcode scan accessory is connected you can trigger a scan by tapping on the VT screen. This is the same behaviour as with the builtin camera. New: The iOS device will not rely anymore on the sound engine of the connected accessory. Instead it will produce sounds itself and additional to the accessory. New: The VT emulation now supports "Double Width Double Height", i.e. the control codes ESC # 3 (Line double width, double height, top half), ESC # 4 (Line double width, double height, low half), ESC # 5 (Line single width, single height), ESC # 6 (Line double width, single height), ESC # : (Line single width, double height, top half), ESC # ; (Line single width, double height, low half). New: The connection parameter „Terminal type“ can be edited. Its default is „vt220“. Change: If you tap the Info button of a running session the session will be aborted and its profile can be edited immediately. Change: The input data stream will now be processed concurrently which yields a better display refresh rate. This will be noticed upon large bulk of data. Change: The accessory connection will be checked continuously. Thus there is no need to restart the app after a connection error. Change: The VT control code sequence CSI ? 5 h CSI ? 5 l can be used to generate a screen flash. Change: If the hostname could not be resolved an error message will be issued. Change: Logdata is more accurate now. Bugfix Telnet protocol: An output control code CR will now be followed by control code NUL unless the new switch „Force Binary Option“ is enabled. Bugfix: The VT control code BEL now generates a sound. Bugfix: The screen reverse mode implementation was incorrect. Bugfix in „Shared Device“ module: You couldn’t erase username and password in a reliable manner. Furthermore the cursor movement was annoying. Bugfix: There were some rendering problems with error and warn messages. Bugfix: There were some rendering problems when changing from portrait to landscape mode or vice versa. Bugfix: Profile names are now guaranteed to be unique. Bugfix: The camera could not be used in landscape mode.

January 26, 2017

Bugfix: A new configuration file could not be deployed to VTconsole by VTconsoleAssistant, if VTconsole was in the state of a fresh installation.

Shared Device

supports fast user switching